思科模拟器:1、路由器单臂路由实现不同VLAN间路由通信 2、三层交换机SVI实现不同VLAN间路由通信
时间: 2023-11-27 12:04:18 浏览: 60
好的,下面我将为您介绍在思科模拟器中如何通过单臂路由和三层交换机SVI实现不同VLAN间的路由通信。
1. 路由器单臂路由实现不同VLAN间路由通信
单臂路由是指将路由器的一个接口与交换机的一个端口连接起来,用来实现不同VLAN之间的路由通信。在思科模拟器中,可以使用以下步骤实现单臂路由:
(1)创建VLAN和端口并将端口配置到相应的VLAN中,例如:
```
Switch(config)# vlan 10
Switch(config-vlan)# name SALES
Switch(config)# interface gigabitethernet 1/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 10
Switch(config)# vlan 20
Switch(config-vlan)# name MARKETING
Switch(config)# interface gigabitethernet 1/2
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 20
```
(2)将路由器的一个接口配置为Trunk链路,并允许通过所有VLAN,例如:
```
Router(config)# interface gigabitethernet 0/0
Router(config-if)# ip address 192.168.1.1 255.255.255.0
Router(config-if)# no shutdown
Router(config-if)# exit
Router(config)# interface gigabitethernet 0/1
Router(config-if)# switchport mode trunk
Router(config-if)# switchport trunk allowed vlan all
Router(config-if)# no shutdown
```
(3)在路由器上创建子接口,并将子接口配置为不同的VLAN,并分配IP地址,例如:
```
Router(config)# interface gigabitethernet 0/1.10
Router(config-if)# encapsulation dot1q 10
Router(config-if)# ip address 192.168.10.1 255.255.255.0
Router(config)# interface gigabitethernet 0/1.20
Router(config-if)# encapsulation dot1q 20
Router(config-if)# ip address 192.168.20.1 255.255.255.0
```
(4)在交换机上配置默认网关,例如:
```
Switch(config)# ip default-gateway 192.168.1.1
```
配置完成后,不同VLAN之间的主机就可以通过路由器的单臂路由实现通信。
2. 三层交换机SVI实现不同VLAN间路由通信
三层交换机可以通过SVI(Switch Virtual Interface)实现不同VLAN之间的路由通信。在思科模拟器中,可以使用以下步骤实现SVI:
(1)创建VLAN并将端口配置到相应的VLAN中,例如:
```
Switch(config)# vlan 10
Switch(config-vlan)# name SALES
Switch(config)# interface gigabitethernet 1/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 10
Switch(config)# vlan 20
Switch(config-vlan)# name MARKETING
Switch(config)# interface gigabitethernet 1/2
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 20
```
(2)在三层交换机上创建SVI,并将SVI配置为不同的VLAN,并分配IP地址,例如:
```
Switch(config)# interface vlan 10
Switch(config-if)# ip address 192.168.10.1 255.255.255.0
Switch(config)# interface vlan 20
Switch(config-if)# ip address 192.168.20.1 255.255.255.0
```
(3)在交换机上配置默认网关,例如:
```
Switch(config)# ip default-gateway 192.168.1.1
```
配置完成后,不同VLAN之间的主机就可以通过三层交换机的SVI实现通信。
以上就是在思科模拟器中通过单臂路由和三层交换机SVI实现不同VLAN间的路由通信的方法。希望对您有所帮助。