stm32 scanf实现
时间: 2023-09-30 19:10:08 浏览: 47
在 STM32 上使用 scanf 函数需要先配置串口通信,并重定向标准输入输出流。
以下是一个基本的示例,演示如何在 STM32 上使用 scanf 函数:
1. 配置串口通信:
```c
#include "stm32f4xx.h"
#include "stdio.h"
void UART_Configuration(void) {
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
// 使能串口时钟和 GPIO 时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
// 配置 USART1 的 TX 引脚为复用功能
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 将 PA9 引脚复用为 USART1 的 TX 引脚
GPIO_PinAFConfig(GPIOA, GPIO_PinSource9, GPIO_AF_USART1);
// 配置 USART1
USART_InitStructure.USART_BaudRate = 115200; // 波特率为 115200
USART_InitStructure.USART_WordLength = USART_WordLength_8b; // 数据位长度为 8 位
USART_InitStructure.USART_StopBits = USART_StopBits_1; // 停止位为 1 位
USART_InitStructure.USART_Parity = USART_Parity_No; // 无奇偶校验
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None; // 无硬件流控制
USART_InitStructure.USART_Mode = USART_Mode_Tx; // 仅发送模式
USART_Init(USART1, &USART_InitStructure);
// 使能 USART1
USART_Cmd(USART1, ENABLE);
}
// 重定向标准输入输出流到 USART1
int fputc(int ch, FILE *f) {
USART_SendData(USART1, (uint8_t)ch);
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
return ch;
}
int fgetc(FILE *f) {
while (USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == RESET);
return (int)USART_ReceiveData(USART1);
}
```
2. 在 main 函数中初始化串口并使用 scanf 函数:
```c
int main(void) {
UART_Configuration(); // 配置串口通信
printf("Please enter a number: ");
fflush(stdout);
int num;
scanf("%d", &num);
printf("You entered: %d\r\n", num);
while (1) {
// 循环执行其他任务
}
}
```
这样就可以在 STM32 上使用 scanf 函数接收用户输入的数据。当用户在终端输入一个数字后,程序会将该数字读入变量 `num` 中,并通过 printf 函数打印出来。
请注意,以上示例代码仅为演示如何在 STM32 上使用 scanf 函数,具体的配置和使用方式可能因不同的 STM32 型号和开发环境而有所差异,你需要根据自己的具体情况进行适当的调整和修改。同时,为了更好地处理输入的数据,你可能还需要添加一些错误处理和数据校验的代码。