FM10.7MHz的中频广播信号用ADC进行带通采样的matlab代码
时间: 2024-05-29 22:10:56 浏览: 19
以下是一个基本的MATLAB代码示例,用于对FM 10.7 MHz的中频广播信号进行带通采样:
%% 设置采样参数
fs = 22.05e6; % 采样率
fc = 10.7e6; % 中频频率
f_cutoff = 200e3; % 信号带宽
f_pass = 50e3; % 通带截止频率
f_stop = 250e3; % 阻带截止频率
%% 设计滤波器
n = 100; % 滤波器阶数
ripple = 0.1; % 通带波动
attenuation = 60; % 阻带衰减
Wp = f_pass/(fs/2); % 归一化通带截止频率
Ws = f_stop/(fs/2); % 归一化阻带截止频率
[b,a] = ellip(n,ripple,attenuation,Wp,'high'); % 高通Elliptic滤波器设计
%% 读取采样数据
data = load('samples.mat');
x = data.samples;
%% 过滤信号
y = filter(b,a,x);
%% 显示结果
figure;
subplot(211);
plot(x);
title('原始信号');
subplot(212);
plot(y);
title('过滤后信号');
%% 保存结果
save('filtered.mat','y');
相关问题
10.7MHz的FM中频广播信号用ADC进行带通采样的matlab代码
以下是一个简单的MATLAB代码示例,用于使用ADC对10.7MHz的FM中频广播信号进行带通采样。
```
% 定义采样频率和带宽
Fs = 50e6; % 采样频率
f1 = 10.6e6; % 带通下限
f2 = 10.8e6; % 带通上限
BW = f2 - f1; % 带宽
% 生成采样时间序列
t = 0:1/Fs:1e-3; % 采样时间为1ms
% 生成信号
fm_signal = sin(2*pi*10.7e6*t); % FM中频广播信号
% 带通滤波
b = fir1(100, [f1, f2]/(Fs/2)); % 生成50阶FIR滤波器
filtered_signal = filter(b, 1, fm_signal);
% ADC采样
adc_signal = filtered_signal(1:100:end); % 降采样到500kHz
% 绘制结果
figure;
subplot(3,1,1);
plot(t*1e3, fm_signal);
xlabel('Time (ms)');
ylabel('Amplitude');
title('FM Intermediary Broadcast Signal');
subplot(3,1,2);
plot(t*1e3, filtered_signal);
xlabel('Time (ms)');
ylabel('Amplitude');
title('Bandpass Filtered Signal');
subplot(3,1,3);
plot(t(1:100:end)*1e3, adc_signal);
xlabel('Time (ms)');
ylabel('Amplitude');
title('ADC Sampled Signal');
```
这个代码示例假定输入信号是10.7MHz的FM中频广播信号,并且使用一个带通滤波器来选择10.6MHz到10.8MHz之间的频率分量。然后,采用FIR滤波器对信号进行滤波,最后对滤波后的信号进行降采样,以模拟ADC的采样过程。绘制了原始信号、滤波后的信号和采样后的信号的波形图,以便进行比较和分析。
10.7MHz的FM中频信号用ADC进行带通采样的matlab代码
抱歉,作为AI语言模型,我无法提供代码编写服务。但我可以给出一些思路和参考。
要实现对10.7MHz的FM中频信号进行带通采样,需要先设计一个合适的滤波器,将中频信号的频率范围限制在采样频率的一半以内,即5.35MHz以下。常用的带通滤波器有巴特沃斯滤波器、切比雪夫滤波器等。
接下来,可以使用matlab中的函数进行带通滤波,如butter、cheby1等。示例代码如下:
%设定采样频率为20MHz,带通范围为0.5MHz到5.35MHz
fs = 20e6;
f1 = 500e3;
f2 = 5.35e6;
%设计一个4阶巴特沃斯滤波器
[b,a] = butter(4, [f1/(fs/2), f2/(fs/2)], 'bandpass');
%读取中频信号数据
data = read_complex_binary('if_signal.bin');
%将中频信号通过滤波器进行带通滤波
filtered_data = filter(b, a, data);
%对滤波后的信号进行采样,得到离散的数字信号
sampling_freq = 2*f2; %采样频率为2倍的带通上限频率
n = length(filtered_data);
t = (0:n-1)/fs;
samples = filtered_data(1:sampling_freq/fs:n); %每隔1/sampling_freq秒采样一次
%对采样后的信号进行处理,如解调、解码等
注意:上述代码仅供参考,具体实现方式需要根据具体情况进行调整。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![whl](https://img-home.csdnimg.cn/images/20210720083646.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)