在cc2530f256中利用串口助手实现cc2530单片机接收pc机发送学号后五位,如果匹配成功,其动跑马灯,否则暂停跑马灯(要求定时器1中断实现)
时间: 2023-11-18 14:04:14 浏览: 33
这个问题需要分为两部分进行解答:串口通信和定时器中断。
#### 1. 串口通信
首先需要在 CC2530 单片机中初始化串口,并设置波特率、数据位、校验位等参数。在接收到 PC 发送的数据后,需要对数据进行处理,提取学号的后五位,并与预设的学号进行比较。如果匹配成功,则向跑马灯控制器发送命令,使其开始跑马灯;否则暂停跑马灯。
以下是串口通信的示例代码:
```c
#include "ioCC2530.h"
void InitUART()
{
PERCFG &= ~0x01; // Set UART1 I/O to P0
P0SEL |= 0x0C; // P0.2, P0.3 used for UART1
P2DIR &= ~0x04; // P2.2 is input
P2SEL &= ~0x04; // P2.2 is GPIO
U1BAUD = 245; // Set baud rate to 9600
U1GCR = 9; // 8 data bits, no parity, 1 stop bit
U1CSR |= 0x80; // Enable UART receiver
}
void main()
{
InitUART();
while (1)
{
if (U1CSR & 0x01) // Check if data is available
{
uint8_t data = U1DBUF; // Read data from UART
if (data == 'S') // Check if it is start of data
{
uint8_t id[5];
for (int i = 0; i < 5; i++)
{
while (!(U1CSR & 0x01)); // Wait for data
id[i] = U1DBUF; // Read data from UART
}
if (strncmp(id, "12345", 5) == 0) // Compare ID
{
// Send command to start marquee
}
else
{
// Send command to stop marquee
}
}
}
}
}
```
#### 2. 定时器中断
为了实现跑马灯的效果,需要使用定时器中断控制 LED 的闪烁。以下是定时器中断的示例代码:
```c
#include "ioCC2530.h"
void InitTimer()
{
T1CTL |= 0x0C; // 32-bit timer mode, prescaler = 8
T1CC0L = 0x00; // Set compare value
T1CC0H = 0x01;
T1IE = 1; // Enable timer 1 interrupt
EA = 1; // Enable global interrupts
T1CTL |= 0x02; // Start timer 1
}
#pragma vector=T1_VECTOR
__interrupt void Timer1_ISR()
{
// Toggle LED
P1_0 ^= 1;
}
```
在上述代码中,我们使用了 32 位定时器,并设置了一个比较值。每当定时器计数器达到比较值时,就会触发定时器中断。在中断处理函数中,我们可以控制 LED 的闪烁。
最后,我们将串口通信和定时器中断结合起来,就可以实现根据学号控制跑马灯的功能了。