汇编语言实现10的阶乘
时间: 2023-07-11 13:27:15 浏览: 47
以下是使用 x86 汇编语言实现计算 10 的阶乘的代码:
```
section .data
n db 10
result dw 1
section .text
global _start
_start:
mov ecx, n ; 将 n 值装入 ecx 寄存器
mov ebx, 1 ; 将 1 值装入 ebx 寄存器
cmp ecx, 0 ; 比较 n 和 0 的大小
jle done ; 如果 n <= 0,则跳转到 done 标签
loop:
mul ebx ; 将 result 乘以 ebx
dec ecx ; 将 n 减 1
cmp ecx, 0 ; 比较 n 和 0 的大小
jg loop ; 如果 n > 0,则跳转到 loop 标签
done:
; 将计算结果存储在 result 变量中
mov [result], ax
; 退出程序
mov eax, 1
xor ebx, ebx
int 0x80
```
在这段代码中,我们将 n 的值设为 10,将 result 的初始值设为 1。然后,我们使用循环依次将 result 乘以 1、2、3、...、10,最后得到的结果即为 10 的阶乘。
相关问题
使用汇编语言实现阶乘函数
以下是使用x86汇编语言实现阶乘函数的示例代码:
```
section .text
global _start
_start:
; 输入要计算阶乘的数
mov eax, 5 ; 例如计算5的阶乘
; 调用阶乘函数
call factorial
; 结果存储在eax中,输出结果
mov ebx, eax
mov eax, 4 ; 4表示sys_write,将输出结果到控制台
mov ecx, msg
mov edx, len
int 0x80
; 退出程序
mov eax, 1 ; 1表示sys_exit,退出程序
xor ebx, ebx ; 返回值为0
int 0x80
factorial:
; 把eax中的值保存在栈中
push eax
; 如果输入为0或1,直接返回1
cmp eax, 1
jle end_factorial
; 否则计算阶乘
dec eax ; eax = eax - 1
call factorial ; 递归调用自己
; eax = eax * (eax + 1)
pop ebx ; 恢复之前保存的eax值
mul ebx ; eax = eax * ebx
end_factorial:
; 返回结果,把eax中的值保存在栈中
push eax
ret
section .data
msg db "The factorial is: ", 0xa ; 输出结果前的提示信息
len equ $ - msg ; 计算提示信息的长度
```
该程序使用递归实现阶乘函数,先保存输入的数值,然后判断是否为0或1,如果是则直接返回1,否则递归调用自己并将结果存储在eax中,最后计算阶乘并返回结果。程序在输出结果前会先输出一个提示信息,然后退出程序。
汇编语言求n阶乘代码
下面是一个使用x86汇编语言实现计算n的阶乘的代码示例:
```
section .data
msg db "Enter a number: ", 0
msg2 db "Factorial of the number is: ", 0
section .bss
n resb 1
section .text
global _start
_start:
; 输出提示信息
mov eax, 4
mov ebx, 1
mov ecx, msg
mov edx, 16
int 0x80
; 输入n
mov eax, 3
mov ebx, 0
mov ecx, n
mov edx, 1
int 0x80
; 计算n的阶乘
mov eax, 1
mov ebx, 0
movzx ecx, byte [n]
loop_start:
cmp ecx, 0
je loop_end
imul eax, ecx
dec ecx
jmp loop_start
loop_end:
; 输出结果
mov eax, 4
mov ebx, 1
mov ecx, msg2
mov edx, 25
int 0x80
; 输出结果
mov eax, 4
mov ebx, 1
mov ecx, eax
mov edx, 1
add ecx, eax
mov byte [ecx], al
mov eax, 4
mov ebx, 1
mov ecx, eax
add ecx, 1
mov edx, 2
int 0x80
; 退出程序
mov eax, 1
xor ebx, ebx
int 0x80
```
这个程序首先提示用户输入一个整数,然后计算该整数的阶乘,最后输出结果并退出程序。