该代码在没有头文件bl_delay.h的情况下怎么修改#include "bl_mcu_sdk.h"#include "bl_gpio.h"#include "bl_adc.h"#include "bl_uart.h"#include "bl_delay.h"#define PRESS_MIN 20#define PRESS_MAX 6000#define VOLTAGE_MIN 150#define VOLTAGE_MAX 3300long map(long x, long in_min, long in_max, long out_min, long out_max);int main(void){ // 初始化延时函数 bl_delay_init(); // 初始化串口 bl_uart_init(0, 9600, UART_BITWIDTH_8BIT, UART_STOP_BIT_1, UART_PARITY_DISABLE); // 初始化ADC bl_adc_init(ADC_CLK_DIV_2, ADC_RESOLUTION_12BIT, ADC_SCALE_4096, ADC_INPUT_MODE_SINGLE, ADC_ATVCC); bl_delay_ms(1000); bl_uart_printf("Test start\n"); while(1) { // 获取ADC采样值 uint16_t value_AD = bl_adc_single_get_value(ADC_0, ADC_CHANNEL_1); // 转换为电压值 int VOLTAGE_AO = map(value_AD, 0, 4095, 0, 3300); if(VOLTAGE_AO < VOLTAGE_MIN) { PRESS_AO = 0; } else if(VOLTAGE_AO > VOLTAGE_MAX) { PRESS_AO = PRESS_MAX; } else { // 根据电压值计算压力值 PRESS_AO = map(VOLTAGE_AO, VOLTAGE_MIN, VOLTAGE_MAX, PRESS_MIN, PRESS_MAX); } // 输出结果 bl_uart_printf("AD value = %d, voltage = %d mV, pressure = %ld g\n", value_AD, VOLTAGE_AO, PRESS_AO); // 延时500ms bl_delay_ms(500); }}long map(long x, long in_min, long in_max, long out_min, long out_max){ return (x - in_min) * (out_max - out_min) / (in_max - in_min) + out_min;}

如果你没有头文件 bl_delay.h，你需要自己实现延时函数，或者使用其他的延时函数库。你可以在代码中定义自己的延时函数，例如：

void delay_ms(uint32_t ms) {
    for (uint32_t i = 0; i < ms; i++) {
        for (uint32_t j = 0; j < 2000; j++) {
            __asm("nop");
        }
    }
}

然后在主函数中使用该延时函数代替 bl_delay_ms()。

int main(void){
    // 初始化串口
    bl_uart_init(0, 9600, UART_BITWIDTH_8BIT, UART_STOP_BIT_1, UART_PARITY_DISABLE);
    // 初始化ADC
    bl_adc_init(ADC_CLK_DIV_2, ADC_RESOLUTION_12BIT, ADC_SCALE_4096, ADC_INPUT_MODE_SINGLE, ADC_ATVCC);
    delay_ms(1000);
    bl_uart_printf("Test start\n");
    while(1)
    {
        // 获取ADC采样值
        uint16_t value_AD = bl_adc_single_get_value(ADC_0, ADC_CHANNEL_1);
        // 转换为电压值
        int VOLTAGE_AO = map(value_AD, 0, 4095, 0, 3300);
        if(VOLTAGE_AO < VOLTAGE_MIN)
        {
            PRESS_AO = 0;
        }
        else if(VOLTAGE_AO > VOLTAGE_MAX)
        {
            PRESS_AO = PRESS_MAX;
        }
        else
        {
            // 根据电压值计算压力值
            PRESS_AO = map(VOLTAGE_AO, VOLTAGE_MIN, VOLTAGE_MAX, PRESS_MIN, PRESS_MAX);
        }
        // 输出结果
        bl_uart_printf("AD value = %d, voltage = %d mV, pressure = %ld g\n", value_AD, VOLTAGE_AO, PRESS_AO);
        // 延时500ms
        delay_ms(500);
    }
}

long map(long x, long in_min, long in_max, long out_min, long out_max){
    return (x - in_min) * (out_max - out_min) / (in_max - in_min) + out_min;
}