stm32实现lcd12864显示 - 串行实现
时间: 2023-09-19 16:03:18 浏览: 145
要实现STM32与LCD12864的串行通信,首先需要连接好硬件电路,将LCD12864的SCL(时钟线)连接到STM32的一个GPIO引脚,将SDA(数据线)连接到另一个GPIO引脚,并连接上电源和地线。
接下来,在STM32的代码中,需要定义对应的GPIO引脚,并进行初始化。通过STM32的寄存器配置,将这两个GPIO引脚设置为输出模式,分别对应SCL和SDA。
然后,就可以编写相关函数,实现与LCD12864之间的通信。在发送数据时,首先需要将SCL设置为高电平,SDA设置为数据的起始位(通常为0);然后通过逐位操作,依次将数据写入SDA引脚;最后将SCL设置为低电平,完成数据的发送。
在接收数据时,需要读取LCD12864的响应。首先将SCL设置为高电平,SDA设置为输入模式;然后通过逐位操作,读取SDA引脚上的数据,并保存下来;最后将SCL设置为低电平,完成数据的接收。
在与LCD12864通信过程中,还需要注意时序的要求。比如,发送数据时,需要保证每两个连续的位之间有一定的时间间隔,而且在结束数据传输之后,还需要等待一段时间,以保证LCD12864正确接收数据。
综上所述,通过STM32实现LCD12864的串行显示,首先要进行正确的硬件连接,然后通过代码初始化GPIO引脚,并编写相应的发送和接收函数,考虑时序要求。这样就能够实现STM32与LCD12864之间的串行通信了。
相关问题
基于stm32的lcd12864串行
如果你想在STM32上使用LCD 12864,你可以使用串行通信协议来控制LCD。这里有几个步骤:
1.选择合适的STM32单片机,并为其设置正确的时钟和引脚。
2.连接LCD 12864并按照其数据手册上的说明来连接STM32的引脚。
3.编写STM32的固件程序,并使用串口通信协议来控制LCD。你可以使用SPI或I2C等通信协议,具体取决于你使用的硬件。
下面是一个使用SPI通信协议的示例代码,你可以根据自己的需要进行修改:
```c
#include "stm32f10x.h"
#include "stm32f10x_spi.h"
#define SPI_PORT GPIOA
#define SPI_PIN_SCK GPIO_Pin_5
#define SPI_PIN_MOSI GPIO_Pin_7
#define SPI_PIN_CS GPIO_Pin_4
void SPI_Init(void)
{
SPI_InitTypeDef SPI_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_SPI1, ENABLE);
GPIO_InitStructure.GPIO_Pin = SPI_PIN_SCK | SPI_PIN_MOSI;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(SPI_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = SPI_PIN_CS;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(SPI_PORT, &GPIO_InitStructure);
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low;
SPI_InitStructure.SPI_CPHA = SPI_CPHA_1Edge;
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_8;
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
SPI_InitStructure.SPI_CRCPolynomial = 7;
SPI_Init(SPI1, &SPI_InitStructure);
SPI_Cmd(SPI1, ENABLE);
}
void SPI_Send(uint8_t data)
{
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_TXE) == RESET);
SPI_I2S_SendData(SPI1, data);
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_RXNE) == RESET);
SPI_I2S_ReceiveData(SPI1);
}
void LCD12864_Init(void)
{
GPIO_SetBits(SPI_PORT, SPI_PIN_CS);
SPI_Send(0xF8); //传输“启动位”
SPI_Send(0x30); //设置8位数据、2行显示、5x7像素
SPI_Send(0x0C); //开启显示、光标关闭、光标闪烁关闭
SPI_Send(0x01); //清屏
SPI_Send(0x06); //文字向右滚动
}
int main(void)
{
SPI_Init();
LCD12864_Init();
while (1)
{
}
}
```
上面的代码中,我们使用SPI通信协议来控制LCD 12864。我们首先初始化SPI,然后发送命令来控制LCD的显示。你可以根据自己的需要来修改代码,例如修改显示的文字、图形等。
STM32串行驱动LCD12864显示屏程序
以下是一个简单的基于STM32的串行驱动LCD12864显示屏程序。它使用的是基于ST的HAL库。
```c
#include "stm32f10x.h"
#include "stm32f10x_gpio.h"
#include "stm32f10x_spi.h"
#define LCD_PORT GPIOA
#define LCD_CS GPIO_Pin_4
#define LCD_A0 GPIO_Pin_5
#define LCD_RST GPIO_Pin_6
void LCD_WriteCmd(uint8_t cmd);
void LCD_WriteData(uint8_t data);
void LCD_Init(void);
void LCD_Clear(void);
void LCD_SetPos(uint8_t x, uint8_t y);
void LCD_WriteChar(uint8_t x, uint8_t y, char c);
void LCD_WriteString(uint8_t x, uint8_t y, char* str);
int main(void)
{
LCD_Init();
LCD_Clear();
LCD_WriteString(0, 0, "Hello, World!");
while(1)
{
}
}
void LCD_WriteCmd(uint8_t cmd)
{
GPIO_ResetBits(LCD_PORT, LCD_A0); // Set A0 low for command
GPIO_ResetBits(LCD_PORT, LCD_CS); // Select LCD
SPI_I2S_SendData(SPI1, cmd); // Send command via SPI
while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY) == SET); // Wait for SPI transmission to complete
GPIO_SetBits(LCD_PORT, LCD_CS); // Deselect LCD
}
void LCD_WriteData(uint8_t data)
{
GPIO_SetBits(LCD_PORT, LCD_A0); // Set A0 high for data
GPIO_ResetBits(LCD_PORT, LCD_CS); // Select LCD
SPI_I2S_SendData(SPI1, data); // Send data via SPI
while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY) == SET); // Wait for SPI transmission to complete
GPIO_SetBits(LCD_PORT, LCD_CS); // Deselect LCD
}
void LCD_Init(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
SPI_InitTypeDef SPI_InitStruct;
// Enable clock for GPIOA and SPI1
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_SPI1, ENABLE);
// Configure GPIO pins
GPIO_InitStruct.GPIO_Pin = LCD_CS | LCD_A0 | LCD_RST;
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(LCD_PORT, &GPIO_InitStruct);
// Reset LCD
GPIO_ResetBits(LCD_PORT, LCD_RST);
GPIO_SetBits(LCD_PORT, LCD_RST);
// Configure SPI
SPI_InitStruct.SPI_Direction = SPI_Direction_1Line_Tx;
SPI_InitStruct.SPI_Mode = SPI_Mode_Master;
SPI_InitStruct.SPI_DataSize = SPI_DataSize_8b;
SPI_InitStruct.SPI_CPOL = SPI_CPOL_Low;
SPI_InitStruct.SPI_CPHA = SPI_CPHA_1Edge;
SPI_InitStruct.SPI_NSS = SPI_NSS_Soft;
SPI_InitStruct.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_4;
SPI_InitStruct.SPI_FirstBit = SPI_FirstBit_MSB;
SPI_InitStruct.SPI_CRCPolynomial = 7;
SPI_Init(SPI1, &SPI_InitStruct);
// Enable SPI
SPI_Cmd(SPI1, ENABLE);
// Initialize LCD
LCD_WriteCmd(0x30);
LCD_WriteCmd(0x0C);
LCD_WriteCmd(0x01);
}
void LCD_Clear(void)
{
uint8_t x, y;
for(x = 0; x < 16; x++)
{
for(y = 0; y < 8; y++)
{
LCD_WriteChar(x, y, ' ');
}
}
}
void LCD_SetPos(uint8_t x, uint8_t y)
{
LCD_WriteCmd(0x80 | (x & 0x0F));
LCD_WriteCmd(0x40 | (y & 0x07));
}
void LCD_WriteChar(uint8_t x, uint8_t y, char c)
{
uint8_t i;
LCD_SetPos(x, y);
for(i = 0; i < 8; i++)
{
LCD_WriteData(Font8x8[c][i]);
}
}
void LCD_WriteString(uint8_t x, uint8_t y, char* str)
{
while(*str)
{
LCD_WriteChar(x++, y, *str++);
}
}
```
注释已经解释了代码的作用。你需要将对应的字库文件添加到代码中,这里使用的是Font8x8,你也可以选择其他字库。该代码可以将任何字符写入LCD屏幕,并在位置(x,y)处显示字符串。