采用一个74x169和一个SSI组件(最多),设计一个模16的计数器.计数序列如下:7,6,5,4,3,2,1,0,8,9,10,11,12,13,14,15,7,
时间: 2024-06-14 21:03:31 浏览: 59
根据提供的引用内容,我们可以得知74x169是一个4位二进制同步计数器,而SSI组件是一个4位二进制加法器。因此,我们可以将它们结合起来设计一个模16的计数器。
具体步骤如下:
1. 将74x169的Q0-Q3引脚连接到SSI组件的A0-A3引脚,将SSI组件的Ci引脚连接到74x169的Clock引脚。
2. 将74x169的MR引脚连接到高电平,以保证计数器从0开始计数。
3. 将SSI组件的B0-B3引脚连接到一个4位二进制常数,该常数的值为7(0111)。
4. 将SSI组件的Si引脚连接到一个单稳态触发器,以产生一个脉冲信号。
5. 将单稳态触发器的输出连接到74x169的Load引脚,以在每次计数结束后将计数器的值加载到SSI组件中。
6. 将SSI组件的Co引脚连接到74x169的CEP引脚,以在计数器达到15时清零。
根据上述步骤,我们可以设计出一个模16的计数器,计数序列为7,6,5,4,3,2,1,0,8,9,10,11,12,13,14,15,7,6,5,4,3,2,1,0,8,9,10,11,12,13,14,15,...。
相关问题
写一个mm32F0144C6p对于W25Q128的SPI_InitTypeDef宏定义代码
好的,以下是mm32F0144C6p对于W25Q128的SPI_InitTypeDef宏定义代码:
```c
typedef struct
{
uint16_t SPI_Direction; /*!< Specifies the SPI unidirectional or bidirectional data mode.
This parameter can be a value of @ref SPI_data_direction */
uint16_t SPI_Mode; /*!< Specifies the SPI operating mode.
This parameter can be a value of @ref SPI_mode */
uint16_t SPI_DataSize; /*!< Specifies the SPI data size.
This parameter can be a value of @ref SPI_data_size */
uint16_t SPI_CPOL; /*!< Specifies the serial clock steady state.
This parameter can be a value of @ref SPI_Clock_Polarity */
uint16_t SPI_CPHA; /*!< Specifies the clock active edge for the bit capture.
This parameter can be a value of @ref SPI_Clock_Phase */
uint16_t SPI_NSS; /*!< Specifies whether the NSS signal is managed by
hardware (NSS pin) or by software using the SSI bit.
This parameter can be a value of @ref SPI_Slave_Select_management */
uint16_t SPI_BaudRatePrescaler; /*!< Specifies the Baud Rate prescaler value which will be
used to configure the transmit and receive SCK clock.
This parameter can be a value of @ref SPI_BaudRate_Prescaler
@note The communication clock is derived from the master
clock. The slave clock does not need to be set. */
uint16_t SPI_FirstBit; /*!< Specifies whether data transfers start from MSB or LSB bit.
This parameter can be a value of @ref SPI_MSB_LSB_transmission */
uint16_t SPI_CRCPolynomial; /*!< Specifies the polynomial used for the CRC calculation. */
}SPI_InitTypeDef;
```
注意:以上代码只定义了结构体的成员,实际使用时还需要根据需要填充具体的值。
如何将部分html 添加到另一个html内
你可以使用如下两种方法将部分 HTML 添加到另一个 HTML 内:
1. 使用框架(Frame)或 iframe 标签:使用框架或 iframe 标签可以将一个 HTML 文档嵌入到另一个 HTML 文档中。在父文档中使用框架或 iframe 标签,并指定子文档的 URL,就可以将子文档的内容嵌入到父文档中。
例如,在父文档中使用 iframe 标签将子文档嵌入:
```html
<iframe src="子文档的 URL"></iframe>
```
2. 使用服务器端包含(SSI):服务器端包含(SSI)是在 Web 服务器上进行处理的技术,可以在 HTML 页面中包含其他文件的内容。在 HTML 页面中使用 SSI 语法,可以将另一个 HTML 文件的内容包含到当前 HTML 文件中。
例如,在 HTML 页面中使用 SSI 包含另一个文件的内容:
```html
<!--#include virtual="文件路径"-->
```
注意,使用服务器端包含需要在 Web 服务器上启用 SSI 功能。