STM32F103ZET6定时器TIM1的PA8/PA9/PA10/PA11输出四路PWM标准库代码

以下是使用标准库在STM32F103ZET6上配置TIM1的代码，以实现四路PWM输出到PA8、PA9、PA10和PA11引脚：

#include "stm32f10x.h"

void TIM1_PWM_Init(void)
{
    GPIO_InitTypeDef GPIO_InitStructure;
    TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
    TIM_OCInitTypeDef TIM_OCInitStructure;

    // 使能TIM1和GPIOA的时钟
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1 | RCC_APB2Periph_GPIOA, ENABLE);

    // 配置PA8、PA9、PA10和PA11引脚为复用推挽输出模式
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10 | GPIO_Pin_11;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

    // 配置TIM1的基本参数
    TIM_TimeBaseStructure.TIM_Period = 999; // 设置周期为1000个计数单位
    TIM_TimeBaseStructure.TIM_Prescaler = 71; // 设置预分频值，得到计数频率为72MHz / (71+1) = 1MHz
    TIM_TimeBaseStructure.TIM_ClockDivision = 0;
    TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
    TIM_TimeBaseInit(TIM1, &TIM_TimeBaseStructure);

    // 配置TIM1的通道1输出参数
    TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
    TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
    TIM_OCInitStructure.TIM_Pulse = 0; // 设置初始占空比为0
    TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
    TIM_OC1Init(TIM1, &TIM_OCInitStructure);
    TIM_OC1PreloadConfig(TIM1, TIM_OCPreload_Enable);

    // 配置TIM1的通道2输出参数
    TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
    TIM_OCInitStructure.TIM_Pulse = 0; // 设置初始占空比为0
    TIM_OC2Init(TIM1, &TIM_OCInitStructure);
    TIM_OC2PreloadConfig(TIM1, TIM_OCPreload_Enable);

    // 配置TIM1的通道3输出参数
    TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
    TIM_OCInitStructure.TIM_Pulse = 0; // 设置初始占空比为0
    TIM_OC3Init(TIM1, &TIM_OCInitStructure);
    TIM_OC3PreloadConfig(TIM1, TIM_OCPreload_Enable);

    // 配置TIM1的通道4输出参数
    TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
    TIM_OCInitStructure.TIM_Pulse = 0; // 设置初始占空比为0
    TIM_OC4Init(TIM1, &TIM_OCInitStructure);
    TIM_OC4PreloadConfig(TIM1, TIM_OCPreload_Enable);

    // 使能TIM1
    TIM_Cmd(TIM1, ENABLE);
}

你可以在你的主函数中调用`TIM1_PWM_Init()`函数来初始化TIM1和GPIO引脚，并使用`TIM_SetCompareX()`函数来设置通道X的占空比（其中X为1、2、3或4）。

请确保在编译和链接过程中包含必要的头文件，并将代码适配到你的开发环境。