stm32f103c8t6蓝牙hc05接收温度数据代码
时间: 2023-07-31 21:13:21 浏览: 57
以下是一个简单的示例代码,使用STM32F103C8T6与HC-05模块进行蓝牙通信,并接收温度数据:
```
#include "stm32f10x.h"
#include "stdio.h"
void USART1_Init(void);
void delay_ms(u16 nms);
int main(void)
{
float temperature = 0;
char buffer[50];
USART1_Init();
while (1)
{
if(USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == SET)
{
char data = USART_ReceiveData(USART1);
if(data == 'T') //接收到温度数据
{
USART_SendData(USART1, 'A'); //发送应答
//接收温度值
while(USART_GetFlagStatus(USART1, USART_FLAG_RXNE) != SET);
temperature = USART_ReceiveData(USART1);
//将温度值转换为实际值
temperature = (float)temperature/10;
//格式化输出温度值
sprintf(buffer, "Temperature: %.1f degrees Celsius\r\n", temperature);
//通过串口发送温度值
for(int i=0; i<strlen(buffer); i++)
{
USART_SendData(USART1, buffer[i]);
while(USART_GetFlagStatus(USART1, USART_FLAG_TXE) != SET);
}
}
}
}
}
void USART1_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_USART1, ENABLE);
//USART1_TX
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
//USART1_RX
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
//USART1配置
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
USART_Cmd(USART1, ENABLE);
}
void delay_ms(u16 nms)
{
u32 i;
for(i=0;i<(72000*nms);i++);
}
```
在此示例代码中,我们使用USART1与HC-05进行通信,并通过串口接收温度数据。当接收到字符'T'时,我们发送一个应答字符'A',然后接收温度数据并将其转换为实际值,并使用sprintf函数将其格式化为字符串,最后通过串口发送温度值。
请注意,此示例代码仅作为参考,并可能需要根据您的具体情况进行修改。