基于rs485的简单现场总线通信系统实现单发单收
时间: 2023-12-01 13:04:41 浏览: 49
要实现基于RS485的简单现场总线通信系统的单发单收,需要以下步骤:
1. 确定通信协议:通信协议是指在通信过程中双方遵循的一种规则。在设计通信协议时,需要确定数据帧的格式、数据传输的方式、校验方式等。
2. 确定硬件连接:RS485通信需要两根数据线A和B,还需要一个共地线。在连接时,需要注意数据线的极性。
3. 设计发送程序:发送程序需要按照通信协议组织数据,并通过串口将数据发送出去。在发送数据之前,需要对数据进行校验,以确保数据的准确性。
4. 设计接收程序:接收程序需要不断监听串口,接收数据,并根据通信协议解析数据。在解析数据时,需要进行校验,以确保数据的准确性。
5. 测试通信:在完成发送程序和接收程序的设计之后,需要进行通信测试,以确保通信正常。
需要注意的是,在实现基于RS485的简单现场总线通信系统时,需要考虑到通信距离、通信速度、数据安全等因素。
相关问题
基于rs485的简单现场总线通信系统单发单收c语言程序
以下是基于RS485的简单现场总线通信系统的单发单收C语言程序示例:
```c
#include <stdio.h>
#include <stdlib.h>
#include <fcntl.h>
#include <unistd.h>
#include <termios.h>
#define BAUDRATE B9600
#define MODEMDEVICE "/dev/ttyS0"
#define _POSIX_SOURCE 1
int set_interface_attribs(int fd, int speed)
{
struct termios tty;
if (tcgetattr(fd, &tty) < 0) {
printf("Error from tcgetattr: %s\n", strerror(errno));
return -1;
}
cfsetospeed(&tty, (speed_t)speed);
cfsetispeed(&tty, (speed_t)speed);
tty.c_cflag |= (CLOCAL | CREAD);
tty.c_cflag &= ~CSIZE;
tty.c_cflag |= CS8;
tty.c_cflag &= ~PARENB;
tty.c_cflag &= ~CSTOPB;
tty.c_cflag &= ~CRTSCTS;
tty.c_lflag &= ~(ICANON | ECHO | ECHOE | ISIG);
tty.c_iflag &= ~(IXON | IXOFF | IXANY);
tty.c_iflag &= ~(IGNBRK|BRKINT|PARMRK|ISTRIP|INLCR|IGNCR|ICRNL);
tty.c_oflag &= ~OPOST;
tty.c_cc[VTIME] = 0;
tty.c_cc[VMIN] = 1;
if (tcsetattr(fd, TCSANOW, &tty) != 0) {
printf("Error from tcsetattr: %s\n", strerror(errno));
return -1;
}
return 0;
}
void set_blocking(int fd, int should_block)
{
struct termios tty;
memset(&tty, 0, sizeof(tty));
if (tcgetattr(fd, &tty) != 0) {
printf("Error from tggetattr: %s\n", strerror(errno));
return;
}
tty.c_cc[VMIN] = should_block ? 1 : 0;
tty.c_cc[VTIME] = 5;
if (tcsetattr(fd, TCSANOW, &tty) != 0)
printf("Error setting term attributes: %s\n", strerror(errno));
}
int main(int argc, char *argv[])
{
int fd;
char buf[256];
char *portname = MODEMDEVICE;
if (argc > 1) {
portname = argv[1];
}
fd = open(portname, O_RDWR | O_NOCTTY | O_SYNC);
if (fd < 0) {
printf("Error opening %s: %s\n", portname, strerror(errno));
return -1;
}
set_interface_attribs(fd, BAUDRATE);
set_blocking(fd, 0);
// 发送数据
char send_buf[] = "Hello, RS485!";
write(fd, send_buf, sizeof(send_buf));
// 接收数据
int n = read(fd, buf, sizeof(buf));
if (n > 0) {
buf[n] = 0;
printf("Received %d bytes: %s\n", n, buf);
}
close(fd);
return 0;
}
```
在这里,我们使用了Linux下的串口通信库`termios`。`set_interface_attribs`函数设置了串口的参数,包括波特率、数据位、停止位等。`set_blocking`函数设置了串口的阻塞方式,如果`should_block`为1表示阻塞读取,否则表示非阻塞读取。在`main`函数中,我们先打开串口设备,然后发送一条数据,再接收一条数据。注意,在RS485总线上,需要在发送和接收数据前进行总线控制,具体方法可以参考RS485总线的通信协议。
基于stc90c516rd单片机rs485简单现场总线通信系统实现单发单收从0~99的发送程序和接收程序
好的,以下是基于stc90c516rd单片机rs485串口通信实现单发单收从0~99的发送程序和接收程序代码示例:
发送程序:
```
#include <reg52.h>
#include <intrins.h>
#define uchar unsigned char
#define uint unsigned int
sbit RS485_EN = P1^7; //定义RS485使能端口
void InitUart(void)
{
SCON = 0x50; //设置串口工作方式
TMOD = 0x20; //设置定时器工作方式
TH1 = 0xfd; //设置波特率为9600
TL1 = 0xfd;
TR1 = 1; //启动定时器1
ES = 1; //使能串口中断
EA = 1; //使能总中断
}
void SendData(uchar dat)
{
SBUF = dat; //将数据放入发送缓冲区
while(!TI); //等待发送完成
TI = 0; //清零发送完成标志
}
void SendCmd(uchar cmd)
{
RS485_EN = 0; //将RS485芯片使能
SendData(cmd); //发送指令
RS485_EN = 1; //关闭RS485芯片使能
}
void main()
{
InitUart(); //初始化串口
while(1)
{
uchar i;
for(i=0; i<100; i++)
{
SendCmd(i); //发送数据
delay(1000); //延时1秒
}
}
}
void UartIsr() interrupt 4
{
uchar dat;
if(RI) //接收到数据
{
RI = 0; //清零接收标志
dat = SBUF; //读取接收缓冲区数据
}
}
```
接收程序:
```
#include <reg52.h>
#include <intrins.h>
#define uchar unsigned char
#define uint unsigned int
sbit RS485_EN = P1^7; //定义RS485使能端口
void InitUart(void)
{
SCON = 0x50; //设置串口工作方式
TMOD = 0x20; //设置定时器工作方式
TH1 = 0xfd; //设置波特率为9600
TL1 = 0xfd;
TR1 = 1; //启动定时器1
ES = 1; //使能串口中断
EA = 1; //使能总中断
}
void SendData(uchar dat)
{
SBUF = dat; //将数据放入发送缓冲区
while(!TI); //等待发送完成
TI = 0; //清零发送完成标志
}
void SendCmd(uchar cmd)
{
RS485_EN = 0; //将RS485芯片使能
SendData(cmd); //发送指令
RS485_EN = 1; //关闭RS485芯片使能
}
void main()
{
InitUart(); //初始化串口
while(1)
{
uchar dat;
if(RI) //接收到数据
{
RI = 0; //清零接收标志
dat = SBUF; //读取接收缓冲区数据
//处理接收到的数据
}
}
}
void UartIsr() interrupt 4
{
uchar dat;
if(RI) //接收到数据
{
RI = 0; //清零接收标志
dat = SBUF; //读取接收缓冲区数据
}
}
```
在程序中,发送程序通过 `SendCmd` 函数发送数据,接收程序通过串口中断接收数据,并在 `main` 函数中处理接收到的数据。需要注意的是,在发送数据时需要将 `RS485_EN` 置为 0,将芯片使能,发送完成后再将其置为 1,关闭芯片使能。在实际使用中,还需要根据具体的硬件连接和协议规定进行适当的修改。
相关推荐
![text/x-c](https://img-home.csdnimg.cn/images/20210720083646.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)