ardunio proteus mixly 温度湿度
时间: 2023-06-25 09:03:15 浏览: 82
可以使用 Arduino、Proteus 和 Mixly 来测量温度和湿度。
1. 使用 DHT11 温湿度传感器连接 Arduino 板。DHT11 有三个引脚:VCC、GND 和 DATA。将 VCC 连接到 Arduino 板的 5V 引脚,GND 连接到 Arduino 板的 GND 引脚,DATA 连接到 Arduino 板的数字引脚 2。
2. 在 Mixly 中编写 Arduino 代码。使用 Adafruit DHT 库来读取 DHT11 传感器的值。示例代码如下:
```
#include <Adafruit_Sensor.h>
#include <DHT.h>
#include <DHT_U.h>
#define DHTPIN 2 // 使用数字引脚 2 连接传感器
#define DHTTYPE DHT11 // 传感器类型为 DHT11
DHT_Unified dht(DHTPIN, DHTTYPE);
void setup() {
Serial.begin(9600);
dht.begin();
}
void loop() {
// 读取温度和湿度
sensors_event_t event;
dht.temperature().getEvent(&event);
float temperature = event.temperature;
dht.humidity().getEvent(&event);
float humidity = event.relative_humidity;
// 输出温度和湿度值
Serial.print("Temperature: ");
Serial.print(temperature);
Serial.print(" °C\t");
Serial.print("Humidity: ");
Serial.print(humidity);
Serial.println(" %");
delay(2000); // 等待 2 秒后再次读取传感器值
}
```
3. 使用 Proteus 模拟电路。在 Proteus 中添加 Arduino UNO 板和 DHT11 传感器模块,并将它们连接起来。
4. 上传代码到 Arduino 板并运行 Proteus 仿真。在串口监视器中查看温度和湿度值的输出。
注意事项:
- 在使用 Proteus 时,需要先在 Arduino IDE 中上传代码到板子上,然后在 Proteus 中加载 HEX 文件。
- 在使用 DHT11 传感器时,需要保持 DATA 引脚的输入输出状态为高电平。如果 DATA 引脚长时间处于低电平状态,可能会导致传感器损坏。
相关推荐
![7z](https://img-home.csdnimg.cn/images/20210720083312.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)