基于stm32c8t6 DHT11工作流程文字说明
时间: 2024-05-26 12:07:04 浏览: 14
基于STM32C8T6和DHT11的工作流程如下:
1. STM32C8T6作为核心处理器,负责控制整个系统的运行。
2. DHT11温湿度传感器模块用于检测环境的温度和湿度。
3. 通过STM32C8T6与DHT11进行通信,读取温湿度传感器的数据。
4. 将读取到的温湿度数据通过OLED显示屏进行显示。
5. 通过ESP8266无线WiFi模块将温湿度数据传输到服务器端。
6. 服务器端将接收到的数据转发到Android端进行显示。
7. 当温度过高时,系统可以触发震动提醒。
这个系统的设计目的是实现基于STM32C8T6和DHT11的温湿度检测和显示,并通过无线WiFi传输到服务器和Android端进行监控和提醒。
相关问题
stm32c8t6 dht11
The STM32C8T6 is a microcontroller based on the ARM Cortex-M3 architecture, developed by STMicroelectronics. It features a 32-bit RISC core with a maximum clock speed of 72 MHz, and a variety of peripherals including timers, ADCs, DACs, and communication interfaces such as UART, SPI, and I2C.
The DHT11 is a low-cost temperature and humidity sensor that uses a digital signal output. It has a measurement range of 0-50°C for temperature and 20-90% for humidity, with an accuracy of ±2°C and ±5% for temperature and humidity, respectively. It communicates with the STM32C8T6 via a one-wire interface, where the microcontroller sends a request signal and the DHT11 responds with the measurement data.
Together, the STM32C8T6 and DHT11 can be used in a variety of applications that require temperature and humidity monitoring, such as environmental control systems, weather stations, and agricultural monitoring.
stm32c8t6 dht11代码
以下是使用STM32C8T6控制DHT11传感器的示例代码:
```C
#include "stm32f10x.h"
// 定义DHT11数据引脚
#define DHT11_DATA_PIN GPIO_Pin_0
#define DHT11_DATA_PORT GPIOA
// 延时函数
void Delay_us(uint32_t us)
{
uint32_t i;
for(i = 0; i < us; i++)
{
__NOP();
}
}
// 初始化DHT11数据引脚
void DHT11_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitStructure.GPIO_Pin = DHT11_DATA_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(DHT11_DATA_PORT, &GPIO_InitStructure);
GPIO_SetBits(DHT11_DATA_PORT, DHT11_DATA_PIN);
}
// 发送信号到DHT11
void DHT11_SendSignal(uint8_t signal)
{
if(signal == 0)
{
GPIO_ResetBits(DHT11_DATA_PORT, DHT11_DATA_PIN); // 拉低引脚
Delay_us(500); // 持续500us
GPIO_SetBits(DHT11_DATA_PORT, DHT11_DATA_PIN); // 拉高引脚
Delay_us(30); // 持续30us
}
else
{
GPIO_ResetBits(DHT11_DATA_PORT, DHT11_DATA_PIN); // 拉低引脚
Delay_us(70); // 持续70us
GPIO_SetBits(DHT11_DATA_PORT, DHT11_DATA_PIN); // 拉高引脚
Delay_us(2); // 持续2us
}
}
// 从DHT11读取数据
uint8_t DHT11_ReadData(void)
{
uint8_t i, j, data = 0;
for(i = 0; i < 8; i++)
{
while(!GPIO_ReadInputDataBit(DHT11_DATA_PORT, DHT11_DATA_PIN)); // 等待引脚变为低电平
Delay_us(40); // 持续40us
if(GPIO_ReadInputDataBit(DHT11_DATA_PORT, DHT11_DATA_PIN) == 1)
{
j = 1;
while(GPIO_ReadInputDataBit(DHT11_DATA_PORT, DHT11_DATA_PIN))
{
Delay_us(1); // 持续1us
j++;
if(j > 100) // 如果超过100us,则退出
{
break;
}
}
if(j > 10) // 如果超过10us,则表示数据为1
{
data |= (1 << (7 - i));
}
}
}
return data;
}
int main(void)
{
uint8_t humi, temp, check;
DHT11_Init();
while(1)
{
DHT11_SendSignal(0); // 发送起始信号
Delay_us(18000); // 持续18ms
DHT11_SendSignal(1); // 发送应答信号
if(!GPIO_ReadInputDataBit(DHT11_DATA_PORT, DHT11_DATA_PIN)) // 如果DHT11响应了应答信号
{
while(GPIO_ReadInputDataBit(DHT11_DATA_PORT, DHT11_DATA_PIN)); // 等待DHT11发送数据
humi = DHT11_ReadData(); // 读取湿度数据
temp = DHT11_ReadData(); // 读取温度数据
check = DHT11_ReadData(); // 读取校验和
if(check == humi + temp) // 如果校验和正确
{
// 处理湿度和温度数据
}
}
}
}
```