Linux i2ctransfer 怎么去读取16位寄存器的值
时间: 2024-02-17 22:04:01 浏览: 74
使用i2ctransfer命令读取16位寄存器的值需要进行以下步骤:
1. 使用i2ctransfer发送写入寄存器地址的命令,将要读取的寄存器地址写入I2C总线:
```
i2ctransfer -y <bus> w3 <address> <reg_high> <reg_low>
```
其中,`<bus>`为I2C总线号,`<address>`为设备地址,`<reg_high>`和`<reg_low>`为16位寄存器地址的高8位和低8位。
2. 使用i2ctransfer发送读取命令,将要读取的16位寄存器的值读取出来:
```
i2ctransfer -y <bus> r2 <address> w1 <data_high> r1 <data_low>
```
其中,`<bus>`和`<address>`同上,`<data_high>`和`<data_low>`为16位寄存器值的高8位和低8位。
完整的读取16位寄存器值的命令如下:
```
i2ctransfer -y <bus> w3 <address> <reg_high> <reg_low> r2 <address> w1 <data_high> r1 <data_low>
```
需要注意的是,不同的设备可能有不同的读写寄存器的方法和规则,因此具体操作还需要参考设备的文档进行。
相关问题
Linux i2c怎么读写芯片16位寄存器
要使用Linux i2c读写芯片的16位寄存器,可以按照以下步骤操作:
1. 打开i2c设备文件,例如/dev/i2c-1。
2. 设置要访问的芯片的地址,使用i2c_smbus_write_byte函数向设备写入地址。
3. 使用i2c_smbus_read_word_data函数读取芯片的16位寄存器值,或使用i2c_smbus_write_word_data函数向芯片的16位寄存器写入数据。
下面是一个简单的例子,展示了如何读取芯片的16位寄存器值:
```
#include <linux/i2c-dev.h>
#include <sys/ioctl.h>
#include <fcntl.h>
int main() {
int file;
char *filename = "/dev/i2c-1";
int addr = 0x50; // 芯片地址
int reg = 0x00; // 要读取的寄存器地址
int data;
// 打开i2c设备文件
if ((file = open(filename, O_RDWR)) < 0) {
printf("Failed to open i2c device\n");
return -1;
}
// 设置要访问的芯片地址
if (ioctl(file, I2C_SLAVE, addr) < 0) {
printf("Failed to set i2c address\n");
return -1;
}
// 读取寄存器值
data = i2c_smbus_read_word_data(file, reg);
printf("Register value: 0x%x\n", data);
close(file);
return 0;
}
```
如果要向芯片的16位寄存器写入数据,可以使用i2c_smbus_write_word_data函数,例如:
```
i2c_smbus_write_word_data(file, reg, data);
```
其中,data是要写入的16位数据。
Linux i2c驱动怎么读写芯片16位寄存器,msg怎么配置
要使用Linux i2c驱动读写芯片的16位寄存器,可以按照以下步骤操作:
1. 定义一个i2c_msg结构体数组,用于存储i2c数据传输的信息,包括要读写的芯片地址、寄存器地址、数据等。
2. 使用ioctl函数设置i2c设备地址(I2C_SLAVE)。
3. 使用read和write函数读写i2c设备。
下面是一个简单的例子,展示了如何使用i2c驱动读取芯片的16位寄存器值:
```
#include <linux/i2c-dev.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <unistd.h>
int main() {
int file;
char *filename = "/dev/i2c-1";
int addr = 0x50; // 芯片地址
int reg = 0x00; // 要读取的寄存器地址
char buf[2];
struct i2c_msg msgs[2] = {
{
.addr = addr,
.flags = 0,
.len = 1,
.buf = ®,
},
{
.addr = addr,
.flags = I2C_M_RD,
.len = 2,
.buf = buf,
},
};
struct i2c_rdwr_ioctl_data msgset = {
.msgs = msgs,
.nmsgs = 2,
};
// 打开i2c设备文件
if ((file = open(filename, O_RDWR)) < 0) {
printf("Failed to open i2c device\n");
return -1;
}
// 设置要访问的芯片地址
if (ioctl(file, I2C_SLAVE, addr) < 0) {
printf("Failed to set i2c address\n");
return -1;
}
// 读取寄存器值
if (ioctl(file, I2C_RDWR, &msgset) < 0) {
printf("Failed to read register\n");
return -1;
}
int data = (buf[0] << 8) | buf[1];
printf("Register value: 0x%x\n", data);
close(file);
return 0;
}
```
在上面的例子中,我们定义了一个i2c_msg结构体数组,包括了要写入的寄存器地址和要读取的数据。然后,我们使用ioctl函数设置了芯片的地址,并使用ioctl函数执行了读取操作。最后,我们从buf中读取了读取到的16位寄存器值。
如果要向芯片的16位寄存器写入数据,可以在msgs数组中添加一条写入数据的消息,例如:
```
char buf[3] = {reg, data >> 8, data & 0xff};
struct i2c_msg msgs[1] = {
{
.addr = addr,
.flags = 0,
.len = 3,
.buf = buf,
},
};
```
其中,data是要写入的16位数据。