void test (int m) { int x=0x11111111; int y=0x22222222; } void main() { test(1); } 画出编译程序对函数test调用时栈分布示意图。
时间: 2024-05-13 19:05:40 浏览: 11
抱歉,作为AI语言模型,我无法画图。不过我可以文字描述。
在函数test调用时,会将参数m压入栈中,然后在栈中为局部变量x和y分配空间,分配顺序与变量声明顺序相同。因此,栈分布示意图如下:
| |
| |
| |
| |
| |
| |
| m |
|-------|
| y |
|-------|
| x |
|-------|
| ... |
其中,空白部分表示栈的未使用空间。注意,栈是向下增长的,因此m的地址最高,x的地址最低。
相关问题
i2c-test -b 2 -s 0x68 -m 1 -rc 5 -d 0x32 0x02 0x04 0x1e 对应的代码
这段命令对应的是使用 i2c 总线读取从设备地址为 0x68 的设备寄存器,寄存器地址为 0x02 的数据,数据长度为 1,重复读取 5 次,每次读取的数据为 0x32 0x02 0x04 0x1e。
下面是使用 C 语言编写的 i2c 读取数据的代码示例:
```c
#include <stdio.h>
#include <fcntl.h>
#include <unistd.h>
#include <linux/i2c-dev.h>
#include <sys/ioctl.h>
int main(void) {
int fd;
char *filename = "/dev/i2c-1"; // i2c 总线设备文件路径
int address = 0x68; // 从设备地址
int reg = 0x02; // 寄存器地址
int len = 1; // 读取数据长度
int repeat = 5; // 重复读取次数
char buf[10] = {0x32, 0x02, 0x04, 0x1e}; // 读取数据缓冲区
// 打开 i2c 总线设备文件
if ((fd = open(filename, O_RDWR)) < 0) {
perror("Failed to open i2c bus");
return 1;
}
// 设置从设备地址
if (ioctl(fd, I2C_SLAVE, address) < 0) {
perror("Failed to set i2c address");
return 1;
}
// 重复读取数据
for (int i = 0; i < repeat; i++) {
// 写入寄存器地址
if (write(fd, ®, 1) != 1) {
perror("Failed to write reg address");
return 1;
}
// 读取数据
if (read(fd, buf, len) != len) {
perror("Failed to read data");
return 1;
}
// 输出读取的数据
printf("Read data: ");
for (int j = 0; j < len; j++) {
printf("%02x ", buf[j]);
}
printf("\n");
}
// 关闭 i2c 总线设备文件
close(fd);
return 0;
}
```
其中,需要注意的是:
- 需要先使用 `open` 函数打开 i2c 总线设备文件,并设置总线地址;
- 使用 `ioctl` 函数设置从设备地址;
- 先写入要读取的寄存器地址,再读取数据;
- 在循环中多次读取数据,直到达到所需的重复次数。
#include<stdio.h> #include<alloca.h> void test(int a) { char *newstack; newstack = (char *)alloca(len); if(newstack) { printf("Alloca(0x%X)returned %p\n",len,newstack); } else printf("Alloca(0x%X) failed\n",len); } void main() { test(256); test(16384); }
在这段代码中,len是没有定义的,因此会导致编译错误。我猜测您想要分配的长度应该为a,因此可以将代码修改为以下形式:
```
#include <stdio.h>
#include <alloca.h>
void test(int a) {
char *newstack;
newstack = (char *)alloca(a);
if(newstack) {
printf("Alloca(0x%X) returned %p\n", a, newstack);
} else {
printf("Alloca(0x%X) failed\n", a);
}
}
int main() {
test(256);
test(16384);
return 0;
}
```
这样就可以正确地使用alloca()函数在堆栈上分配指定大小的内存,并输出分配的内存地址。同时,为了使程序更加规范,我也将main()函数的返回值类型修改为int,并加上了return语句。