基于stm32f103c8t6控制MQ-7代码
时间: 2023-08-01 17:09:03 浏览: 73
对于基于STM32F103C8T6控制MQ-7传感器的代码,需要涉及到模拟输入、串口通信和ADC转换等模块。
以下是一个简单的代码示例:
```c
#include "stm32f10x.h"
#define MQ7_PORT GPIOA
#define MQ7_PIN GPIO_Pin_0
void init_ADC1(void) {
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
ADC_InitTypeDef ADC_InitStructure;
ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;
ADC_InitStructure.ADC_ScanConvMode = DISABLE;
ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
ADC_InitStructure.ADC_NbrOfChannel = 1;
ADC_Init(ADC1, &ADC_InitStructure);
ADC_Cmd(ADC1, ENABLE);
}
uint16_t read_ADC1(uint8_t channel) {
ADC_RegularChannelConfig(ADC1, channel, 1, ADC_SampleTime_239Cycles5);
ADC_SoftwareStartConvCmd(ADC1, ENABLE);
while (ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET);
return ADC_GetConversionValue(ADC1);
}
int main(void) {
// 初始化GPIO
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = MQ7_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_Init(MQ7_PORT, &GPIO_InitStructure);
// 初始化ADC
init_ADC1();
// 初始化串口
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
USART_InitTypeDef USART_InitStructure;
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
USART_Cmd(USART1, ENABLE);
while (1) {
// 读取MQ7传感器的模拟值
uint16_t mq7_value = read_ADC1(0);
// 将模拟值转换为可读的数据
// 可以根据MQ7的数据手册进行计算
float mq7_ppm = mq7_value * 5.0 / 4096.0;
// 发送数据到串口
char buffer[32];
sprintf(buffer, "MQ7 PPM: %f\r\n", mq7_ppm);
USART_SendData(USART1, buffer, strlen(buffer));
delay_ms(1000);
}
}
```
这段代码主要实现了以下功能:
1. 初始化ADC和串口模块;
2. 循环读取MQ7传感器的模拟值,转换为可读的数据,并发送到串口;
3. 在发送数据之间添加延迟,以避免过于频繁的数据发送。
需要注意的是,这段代码仅供参考,实际使用时需要根据具体的硬件情况进行调整。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![txt](https://img-home.csdnimg.cn/images/20210720083642.png)