STM32F103C8T6的锂电池电量检测代码
时间: 2023-09-22 20:11:52 浏览: 99
以下是基于STM32F103C8T6的锂电池电量检测代码,其中使用了ADC模块进行电量检测:
```c
#include "stm32f10x.h"
#define ADC1_DR_Address ((u32)0x4001244C)
void RCC_Configuration(void);
void GPIO_Configuration(void);
void ADC_Configuration(void);
u16 ADC_ConvertedValue;
int main(void)
{
RCC_Configuration(); // 配置系统时钟
GPIO_Configuration(); // 配置GPIO
ADC_Configuration(); // 配置ADC
ADC_SoftwareStartConvCmd(ADC1, ENABLE); // 开始进行ADC转换
while (1)
{
// 循环检测ADC转换完成标志位
while(!ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC));
ADC_ConvertedValue = ADC_GetConversionValue(ADC1); // 获取ADC转换结果
/*
根据电压与参考电压之比计算电池电量百分比
假设电压测量范围为3.0V~4.2V,对应ADC值范围为0~4095
参考电压为3.3V
*/
u8 battery_percentage = (ADC_ConvertedValue * 100) / 4095 * (4.2 - 3.0) / 3.3;
// 将电量百分比输出到调试串口
printf("Battery percentage: %d%%\n", battery_percentage);
delay_ms(1000); // 延时1秒钟
}
}
void RCC_Configuration(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE); // 使能GPIOA时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE); // 使能ADC1时钟
}
void GPIO_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// 配置PA0为模拟输入引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
}
void ADC_Configuration(void)
{
ADC_InitTypeDef ADC_InitStructure;
ADC_DeInit(ADC1); // 复位ADC1
ADC_InitStructure.ADC_Mode = ADC_Mode_Independent; // 独立模式
ADC_InitStructure.ADC_ScanConvMode = DISABLE; // 单通道模式
ADC_InitStructure.ADC_ContinuousConvMode = DISABLE; // 单次转换模式
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None; // 转换触发源
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right; // 数据右对齐
ADC_InitStructure.ADC_NbrOfChannel = 1; // 转换通道数
ADC_Init(ADC1, &ADC_InitStructure);
ADC_Cmd(ADC1, ENABLE); // 使能ADC1
ADC_ResetCalibration(ADC1); // 复位校准寄存器
while (ADC_GetResetCalibrationStatus(ADC1)); // 等待校准寄存器复位完成
ADC_StartCalibration(ADC1); // 开始校准
while (ADC_GetCalibrationStatus(ADC1)); // 等待校准完成
/*
配置ADC通道0,采样时间为55.5个时钟周期,采样时钟为PCLK2的8分频,
即72MHz / 8 = 9MHz,对应采样周期为111ns
*/
ADC_RegularChannelConfig(ADC1, ADC_Channel_0, 1, ADC_SampleTime_55Cycles5);
ADC_TempSensorVrefintCmd(DISABLE); // 关闭温度传感器和内部参考电压的测量
}
```
注:以上代码仅供参考,具体实现要根据硬件电路设计进行调整。同时,为了保证电量检测的准确性和安全性,建议在系统中增加过压保护、欠压保护等功能。
相关推荐
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)