帮助您编写dht11温湿度传感器的stm32程序。
时间: 2023-11-02 21:05:41 浏览: 42
以下是使用STM32编写DHT11温湿度传感器程序的简单步骤和代码:
步骤1:配置GPIO引脚
首先,需要将STM32的GPIO引脚配置为输入模式,以读取传感器数据。在此示例中,我们将使用PA1引脚作为DHT11传感器的数据引脚。
// Enable GPIOA clock
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
// Configure PA1 as input
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
步骤2:发送启动信号
为了读取温湿度数据,需要通过DHT11传感器发送启动信号。启动信号由主机发送,它应该拉低数据线至少18毫秒,然后拉高数据线20到40微秒。
// Send start signal
GPIO_ResetBits(GPIOA, GPIO_Pin_1);
delay_ms(18);
GPIO_SetBits(GPIOA, GPIO_Pin_1);
delay_us(40);
步骤3:接收数据
在发送启动信号后,DHT11将发送40位数据,其中包括湿度,温度和校验和。每个数据位的持续时间为50微秒,高电平表示1,低电平表示0。在读取每个数据位之后,需要等待一段时间以准备读取下一个数据位。
// Read data bits
for (int i = 0; i < 40; i++) {
// Wait for data bit
while (GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_1) == RESET);
// Measure high pulse width
uint32_t high_pulse_width = 0;
while (GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_1) == SET) {
high_pulse_width++;
delay_us(1);
}
// Check if bit is 1 or 0
if (high_pulse_width > 40) {
data[i / 8] |= (1 << (7 - (i % 8)));
}
}
步骤4:解码数据
读取数据后,需要将它们解码为湿度,温度和校验和。这可以通过将前两个8位数据组合在一起来实现湿度和温度,并将校验和与前两个数据的和进行比较来验证数据的准确性。
// Decode data
uint8_t humidity = data[0];
uint8_t temperature = data[2];
uint8_t checksum = data[4];
if ((humidity + temperature) == checksum) {
// Data is valid
} else {
// Data is invalid
}
完整的代码示例:
#include "stm32f10x.h"
void delay_us(uint32_t us)
{
us *= (SystemCoreClock / 1000000) / 5;
while (us--) {
__NOP();
}
}
void delay_ms(uint32_t ms)
{
while (ms--) {
delay_us(1000);
}
}
int main(void)
{
// Enable GPIOA clock
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
// Configure PA1 as input
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Send start signal
GPIO_ResetBits(GPIOA, GPIO_Pin_1);
delay_ms(18);
GPIO_SetBits(GPIOA, GPIO_Pin_1);
delay_us(40);
// Read data bits
uint8_t data[5] = {0};
for (int i = 0; i < 40; i++) {
// Wait for data bit
while (GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_1) == RESET);
// Measure high pulse width
uint32_t high_pulse_width = 0;
while (GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_1) == SET) {
high_pulse_width++;
delay_us(1);
}
// Check if bit is 1 or 0
if (high_pulse_width > 40) {
data[i / 8] |= (1 << (7 - (i % 8)));
}
}
// Decode data
uint8_t humidity = data[0];
uint8_t temperature = data[2];
uint8_t checksum = data[4];
if ((humidity + temperature) == checksum) {
// Data is valid
} else {
// Data is invalid
}
while (1) {
// Loop forever
}
}
相关推荐
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)