esp8266和stm32串口通信如何实现
时间: 2023-08-27 12:12:04 浏览: 40
实现ESP8266和STM32之间的串口通信,需要以下几个步骤:
1. 确定串口通信参数:波特率、数据位、停止位、校验位等。
2. 在STM32上初始化串口,设置串口通信参数。
3. 在ESP8266上使用AT指令设置串口通信参数,确保与STM32设置一致。
4. 在STM32上使用串口发送数据,通过TX引脚将数据发送到ESP8266的RX引脚。
5. 在ESP8266上接收到数据后,通过AT指令将数据发送到串口输出,或者通过AT指令将数据发送到云端。
以下是一个简单的ESP8266和STM32串口通信的示例代码:
STM32部分代码:
```c
#include "stm32f10x.h"
#include "stdio.h"
void USART1_Config(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
/* Enable GPIO clock */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
/* Enable USART clock */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
/* Configure USART1 Tx (PA9) as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/* Configure USART1 Rx (PA10) as input floating */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/* Configure USART1 */
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
/* Enable USART1 */
USART_Cmd(USART1, ENABLE);
}
void USART1_SendChar(char ch)
{
/* Wait until transmit data register is empty */
while(USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
/* Send character */
USART_SendData(USART1, ch);
}
void USART1_SendString(char* str)
{
while(*str)
{
USART1_SendChar(*str++);
}
}
int main(void)
{
USART1_Config();
while(1)
{
USART1_SendString("Hello, World!\r\n");
DelayMs(1000);
}
}
```
ESP8266部分代码:
```c
#include <SoftwareSerial.h>
SoftwareSerial mySerial(10, 11); // RX, TX
void setup()
{
Serial.begin(115200);
mySerial.begin(115200); // Initialize ESP8266 serial port
mySerial.println("AT+UART=115200,8,1,0,0"); // Set serial parameters
}
void loop()
{
if (mySerial.available())
{
Serial.write(mySerial.read());
}
if (Serial.available())
{
mySerial.write(Serial.read());
}
}
```
在上述代码中,STM32通过USART1向串口发送数据,ESP8266通过SoftwareSerial库模拟UART通信,接收STM32发送的数据。在ESP8266的setup()函数中,通过AT指令设置串口通信参数。在ESP8266的loop()函数中,通过mySerial.available()和Serial.available()判断是否有数据需要发送或接收。