基于stm32写一个温度系统代码
时间: 2024-01-24 22:04:13 浏览: 32
好的,以下是基于STM32写一个温度系统的代码示例,仅供参考:
```c
#include "main.h"
#include "stdio.h"
// 定义温度传感器DS18B20的GPIO口
#define DS18B20_GPIO_Port GPIOA
#define DS18B20_Pin GPIO_PIN_5
// 定义OLED显示屏的SPI口
#define OLED_SPI_Port hspi1
// 定义温度传感器读取命令
#define DS18B20_READ_ROM 0x33
#define DS18B20_CONVERT_T 0x44
#define DS18B20_READ_SCRATCHPAD 0xBE
// 声明温度传感器函数
void DS18B20_Init(void);
void DS18B20_Reset(void);
void DS18B20_Write_Byte(uint8_t data);
uint8_t DS18B20_Read_Byte(void);
void DS18B20_Convert_T(void);
float DS18B20_Read_T(void);
// 声明OLED屏幕函数
void OLED_Init(void);
void OLED_Clear(void);
void OLED_ShowString(uint8_t x, uint8_t y, uint8_t *chr, uint8_t Char_Size);
// 声明全局变量
float temperature = 0; // 温度值
int main(void)
{
// 初始化HAL库
HAL_Init();
// 配置系统时钟
SystemClock_Config();
// 配置GPIO口、串口、SPI等外设
MX_GPIO_Init();
MX_USART1_UART_Init();
MX_SPI1_Init();
// 初始化温度传感器
DS18B20_Init();
// 初始化OLED显示屏
OLED_Init();
OLED_Clear();
OLED_ShowString(0, 0, "Temperature:", 16);
while (1)
{
// 读取温度值
temperature = DS18B20_Read_T();
// 温度值转换为字符串
uint8_t str[16];
sprintf((char *)str, "%.2f C", temperature);
// 在OLED屏幕上显示温度值
OLED_ShowString(0, 16, str, 16);
HAL_Delay(1000); // 延时1秒
}
}
// 温度传感器初始化函数
void DS18B20_Init(void)
{
GPIO_InitTypeDef GPIO_InitStruct = {0};
// 配置DS18B20的GPIO口
GPIO_InitStruct.Pin = DS18B20_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(DS18B20_GPIO_Port, &GPIO_InitStruct);
// 复位DS18B20
DS18B20_Reset();
}
// 温度传感器复位函数
void DS18B20_Reset(void)
{
HAL_GPIO_WritePin(DS18B20_GPIO_Port, DS18B20_Pin, GPIO_PIN_RESET); // 输出低电平
HAL_Delay(480); // 延时480us
HAL_GPIO_WritePin(DS18B20_GPIO_Port, DS18B20_Pin, GPIO_PIN_SET); // 输出高电平
HAL_Delay(60); // 延时60us
uint8_t presence = HAL_GPIO_ReadPin(DS18B20_GPIO_Port, DS18B20_Pin); // 读取应答信号
HAL_Delay(420); // 延时420us
}
// 温度传感器写入一个字节的数据
void DS18B20_Write_Byte(uint8_t data)
{
for (uint8_t i = 0; i < 8; i++)
{
if ((data >> i) & 0x01)
{
HAL_GPIO_WritePin(DS18B20_GPIO_Port, DS18B20_Pin, GPIO_PIN_RESET); // 输出低电平
HAL_Delay(2); // 延时2us
HAL_GPIO_WritePin(DS18B20_GPIO_Port, DS18B20_Pin, GPIO_PIN_SET); // 输出高电平
HAL_Delay(60); // 延时60us
}
else
{
HAL_GPIO_WritePin(DS18B20_GPIO_Port, DS18B20_Pin, GPIO_PIN_RESET); // 输出低电平
HAL_Delay(60); // 延时60us
HAL_GPIO_WritePin(DS18B20_GPIO_Port, DS18B20_Pin, GPIO_PIN_SET); // 输出高电平
HAL_Delay(2); // 延时2us
}
}
}
// 温度传感器读取一个字节的数据
uint8_t DS18B20_Read_Byte(void)
{
uint8_t data = 0;
for (uint8_t i = 0; i < 8; i++)
{
HAL_GPIO_WritePin(DS18B20_GPIO_Port, DS18B20_Pin, GPIO_PIN_RESET); // 输出低电平
HAL_Delay(2); // 延时2us
HAL_GPIO_WritePin(DS18B20_GPIO_Port, DS18B20_Pin, GPIO_PIN_SET); // 输出高电平
HAL_Delay(8); // 延时8us
if (HAL_GPIO_ReadPin(DS18B20_GPIO_Port, DS18B20_Pin))
{
data |= (0x01 << i);
}
HAL_Delay(50); // 延时50us
}
return data;
}
// 温度传感器发起温度转换
void DS18B20_Convert_T(void)
{
DS18B20_Reset(); // 复位
DS18B20_Write_Byte(DS18B20_SKIP_ROM); // 跳过ROM操作
DS18B20_Write_Byte(DS18B20_CONVERT_T); // 发起温度转换
}
// 温度传感器读取温度值
float DS18B20_Read_T(void)
{
uint8_t scratchpad[9]; // 定义读取缓存
DS18B20_Convert_T(); // 发起温度转换
DS18B20_Reset(); // 复位
DS18B20_Write_Byte(DS18B20_SKIP_ROM); // 跳过ROM操作
DS18B20_Write_Byte(DS18B20_READ_SCRATCHPAD); // 读取温度值
for (uint8_t i = 0; i < 9; i++)
{
scratchpad[i] = DS18B20_Read_Byte(); // 逐个读取
}
float temp = (float)(scratchpad[1] << 8 | scratchpad[0]) / 16.0f; // 计算温度值
return temp;
}
// OLED显示屏初始化函数
void OLED_Init(void)
{
// 初始化OLED屏幕
// 设置OLED显示屏SPI口
OLED_SPI_Port.Instance = SPI1;
OLED_SPI_Port.Init.Mode = SPI_MODE_MASTER;
OLED_SPI_Port.Init.Direction = SPI_DIRECTION_2LINES;
OLED_SPI_Port.Init.DataSize = SPI_DATASIZE_8BIT;
OLED_SPI_Port.Init.CLKPolarity = SPI_POLARITY_LOW;
OLED_SPI_Port.Init.CLKPhase = SPI_PHASE_1EDGE;
OLED_SPI_Port.Init.NSS = SPI_NSS_SOFT;
OLED_SPI_Port.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_16;
OLED_SPI_Port.Init.FirstBit = SPI_FIRSTBIT_MSB;
OLED_SPI_Port.Init.TIMode = SPI_TIMODE_DISABLE;
OLED_SPI_Port.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
OLED_SPI_Port.Init.CRCPolynomial = 10;
if (HAL_SPI_Init(&OLED_SPI_Port) != HAL_OK)
{
Error_Handler();
}
// 初始化OLED显示屏
OLED_Init();
}
// OLED显示屏清屏函数
void OLED_Clear(void)
{
OLED_ShowString(0, 0, " ", 16);
OLED_ShowString(0, 16, " ", 16);
}
// OLED显示屏显示字符串函数
void OLED_ShowString(uint8_t x, uint8_t y, uint8_t *chr, uint8_t Char_Size)
{
unsigned char c = 0, i = 0, j = 0;
while (chr[j] != '\0')
{
c = chr[j] - 32;
if (x > 128 - 1)
{
x = 0;
y += 16;
}
if (y > 64 - 1)
{
y = x = 0;
OLED_Clear();
}
OLED_Set_Pos(x, y);
for (i = 0; i < Char_Size; i++)
{
OLED_WR_DATA(F8X16[c * 16 + i]);
}
x += 8;
j++;
}
}
```
以上代码仅供参考,实际应用中需要根据具体硬件和软件情况进行修改和优化。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)