串口:发送0:点亮灯;发送1:关闭灯程序怎么写
时间: 2024-03-07 09:46:42 浏览: 27
如果你正在使用Python语言,你可以使用PySerial库来读取串口数据。以下是一个示例程序,可以读取串口数据并执行相应的操作:
```python
import serial
# 打开串口
ser = serial.Serial('/dev/ttyS0', 9600)
while True:
# 读取串口数据
data = ser.readline().decode().strip()
# 判断数据并执行相应的操作
if data == '0':
# 点亮灯
print('Turn on the light.')
elif data == '1':
# 关闭灯
print('Turn off the light.')
```
在上面的代码中,我们首先使用`serial.Serial()`函数打开串口,指定串口的端口号和波特率。然后使用一个死循环来不断读取串口数据,使用`ser.readline()`函数读取一行数据,并使用`decode()`方法将字节数据转换成字符串。然后我们判断读取到的数据是否为0或1,如果是0则打印“Turn on the light.”,如果是1则打印“Turn off the light.”。
需要注意的是,在你的设备上,串口的端口号和波特率可能会不同,你需要根据你的实际情况进行修改。
相关问题
串口:发送0:点亮灯;发送1:关闭灯程序C语言怎么写
如果你想在C语言中编写读取串口数据的程序,你可以使用`termios`和`fcntl`库来控制串口通信。以下是一个示例程序:
```c
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <fcntl.h>
#include <termios.h>
#include <unistd.h>
int main()
{
int fd;
struct termios options;
char buf[255];
// 打开串口
fd = open("/dev/ttyS0", O_RDWR | O_NOCTTY | O_NDELAY);
if (fd == -1) {
printf("Error opening serial port.\n");
return -1;
}
// 配置串口
fcntl(fd, F_SETFL, 0);
tcgetattr(fd, &options);
cfsetispeed(&options, B9600);
cfsetospeed(&options, B9600);
options.c_cflag |= (CLOCAL | CREAD);
options.c_cflag &= ~PARENB;
options.c_cflag &= ~CSTOPB;
options.c_cflag &= ~CSIZE;
options.c_cflag |= CS8;
options.c_cc[VMIN] = 1;
options.c_cc[VTIME] = 0;
tcsetattr(fd, TCSANOW, &options);
while (1) {
// 读取串口数据
int n = read(fd, buf, sizeof(buf));
if (n > 0) {
buf[n] = '\0';
if (strcmp(buf, "0") == 0) {
// 点亮灯
printf("Turn on the light.\n");
} else if (strcmp(buf, "1") == 0) {
// 关闭灯
printf("Turn off the light.\n");
}
}
}
// 关闭串口
close(fd);
return 0;
}
```
在上面的代码中,我们首先使用`open()`函数打开串口,指定串口的端口号和打开方式。然后使用`fcntl()`函数将串口设置为阻塞模式,使用`tcgetattr()`和`tcsetattr()`函数设置串口的波特率和参数。然后我们进入一个死循环,不断读取串口数据,并使用`strcmp()`函数判断读取到的数据是否为0或1,如果是0则打印“Turn on the light.”,如果是1则打印“Turn off the light.”。
需要注意的是,在你的设备上,串口的端口号和波特率可能会不同,你需要根据你的实际情况进行修改。
用Arduino C语言写一个程序,串口收到‘1’点亮13号引脚的LED灯,收到‘2’关闭led灯,写出程序
### 回答1:
int ledPin = 13;void setup()
{
pinMode(ledPin, OUTPUT);
Serial.begin(9600);
}void loop()
{
if(Serial.available() > 0)
{
char ch = Serial.read();
if(ch == '1')
{
digitalWrite(ledPin, HIGH);
}
else if(ch == '2')
{
digitalWrite(ledPin, LOW);
}
}
}
### 回答2:
下面是使用Arduino C语言编写的程序:
```c
int ledPin = 13; // LED连接的引脚
void setup() {
Serial.begin(9600); // 设置串口通信波特率为9600
pinMode(ledPin, OUTPUT); // 设置引脚模式为输出
}
void loop() {
if (Serial.available() > 0) { // 如果串口接收到字符
char command = Serial.read(); // 读取字符
if (command == '1') { // 如果接收到字符‘1’
digitalWrite(ledPin, HIGH); // 点亮LED灯
Serial.println("LED灯已点亮");
} else if (command == '2') { // 如果接收到字符‘2’
digitalWrite(ledPin, LOW); // 关闭LED灯
Serial.println("LED灯已关闭");
}
}
}
```
以上程序定义了一个整数变量`ledPin`,用于存储LED连接的引脚号(这里是13号引脚)。在`setup()`函数中,初始化串口通信并设置引脚模式为输出。在`loop()`函数中,通过判断串口接收到的字符,来控制LED的亮灭。如果接收到字符‘1’,则点亮LED灯并通过串口向计算机发送消息“LED灯已点亮”。如果接收到字符‘2’,则关闭LED灯并通过串口向计算机发送消息“LED灯已关闭”。
你可以使用Arduino开发环境将上述程序上传到Arduino单片机中,然后通过串口发送字符‘1’或‘2’来控制LED灯的亮灭。
### 回答3:
下面是使用Arduino C语言编写的程序, 当串口接收到'1'时点亮13号引脚的LED灯, 当接收到'2'时关闭LED灯。
```c
int ledPin = 13; // 设置LED灯的引脚号
void setup() {
pinMode(ledPin, OUTPUT); // 设置LED引脚为输出模式
Serial.begin(9600); // 初始化串口通信,波特率为9600
}
void loop() {
if (Serial.available() > 0) { // 如果串口接收到数据
char receivedChar = Serial.read(); // 读取串口接收到的数据
if (receivedChar == '1') {
digitalWrite(ledPin, HIGH); // 点亮LED灯
Serial.println("LED灯已点亮");
} else if (receivedChar == '2') {
digitalWrite(ledPin, LOW); // 关闭LED灯
Serial.println("LED灯已关闭");
}
}
}
```
在上述程序中,初始化了一个变量`ledPin`来保存LED灯的引脚号,这里采用的是13号引脚。在`setup()`函数中,将13号引脚设置为输出模式,并使用`Serial.begin(9600)`来初始化串口通信,设置波特率为9600。
在`loop()`函数中,使用`Serial.available()`函数来判断是否有数据接收到。如果有数据接收到,调用`Serial.read()`函数来读取数据,并保存在`receivedChar`变量中。
然后使用`if`语句判断接收到的字符是'1'还是'2',如果是'1',则调用`digitalWrite(ledPin, HIGH)`来点亮LED灯,并通过`Serial.println()`函数在串口打印提示信息。如果是'2',则调用`digitalWrite(ledPin, LOW)`来关闭LED灯。
程序会在`loop()`函数中不断循环执行,以便接收和处理串口数据。