写一个mm32F0144C6p对于W25Q128的SPI_SendData代码
时间: 2024-03-12 16:48:56 浏览: 29
好的,以下是一个简单的mm32F0144C6p对于W25Q128的SPI_SendData代码:
```
void SPI_SendData(uint8_t data) {
while (SPI_GetFlagStatus(SPI_FLAG_TXE) == RESET); //等待发送缓冲区为空
SPI_SendData(SPI1, data); //发送数据
while (SPI_GetFlagStatus(SPI_FLAG_RXNE) == RESET); //等待接收缓冲区有数据
SPI_ReceiveData(SPI1); //清除接收缓冲区
}
```
在这个代码中,我们使用了mm32F0144C6p的SPI1模块来与W25Q128进行SPI通信。我们使用while循环来等待发送缓冲区为空和接收缓冲区有数据。然后使用SPI_SendData函数发送数据,并使用SPI_ReceiveData函数清除接收缓冲区。
需要注意的是,这个代码只是一个简单的示例,实际的代码可能需要更加复杂,具体要根据实际情况来进行调整。同时,还需要根据具体的硬件连接,来设置SPI的时钟、数据位数、极性等参数。
相关问题
写一个mm32f0144c6p对于w25q128的SPI_SendData代码
以下是一个简单的mm32f0144c6p对于w25q128的SPI_SendData代码:
```c
#include "mm32f0144.h"
#include "w25q128.h"
void SPI_SendData(uint8_t data) {
while ((SPI1->SR & SPI_SR_BSY) != 0); //等待SPI忙碌标志位被清除
SPI1->DR = data; //将数据写入SPI数据寄存器
while ((SPI1->SR & SPI_SR_RXNE) == 0); //等待SPI接收缓冲区非空标志位被设置
SPI1->DR; //读取接收到的数据
}
```
请注意,这只是一个简单的示例代码,你需要根据实际情况和要求进行修改和调整。同时,为了使代码更加完整和可用,你需要包含SPI控制器的初始化和其他必要的函数和库。
写一个mm32F0144C6p对于W25Q128的SPI_InitTypeDef宏定义代码
好的,以下是mm32F0144C6p对于W25Q128的SPI_InitTypeDef宏定义代码:
```c
typedef struct
{
uint16_t SPI_Direction; /*!< Specifies the SPI unidirectional or bidirectional data mode.
This parameter can be a value of @ref SPI_data_direction */
uint16_t SPI_Mode; /*!< Specifies the SPI operating mode.
This parameter can be a value of @ref SPI_mode */
uint16_t SPI_DataSize; /*!< Specifies the SPI data size.
This parameter can be a value of @ref SPI_data_size */
uint16_t SPI_CPOL; /*!< Specifies the serial clock steady state.
This parameter can be a value of @ref SPI_Clock_Polarity */
uint16_t SPI_CPHA; /*!< Specifies the clock active edge for the bit capture.
This parameter can be a value of @ref SPI_Clock_Phase */
uint16_t SPI_NSS; /*!< Specifies whether the NSS signal is managed by
hardware (NSS pin) or by software using the SSI bit.
This parameter can be a value of @ref SPI_Slave_Select_management */
uint16_t SPI_BaudRatePrescaler; /*!< Specifies the Baud Rate prescaler value which will be
used to configure the transmit and receive SCK clock.
This parameter can be a value of @ref SPI_BaudRate_Prescaler
@note The communication clock is derived from the master
clock. The slave clock does not need to be set. */
uint16_t SPI_FirstBit; /*!< Specifies whether data transfers start from MSB or LSB bit.
This parameter can be a value of @ref SPI_MSB_LSB_transmission */
uint16_t SPI_CRCPolynomial; /*!< Specifies the polynomial used for the CRC calculation. */
}SPI_InitTypeDef;
```
注意:以上代码只定义了结构体的成员,实际使用时还需要根据需要填充具体的值。