Ze08甲醛传感器和stm32f103c8t6,通过PB10、PB11UART通信,传感器采用问答式检测,程序设计
时间: 2023-10-11 19:10:36 浏览: 43
好的,下面是一份基于STM32F103C8T6和Ze08甲醛传感器的UART通信问答式检测的程序设计:
```c
#include "stm32f10x.h"
#include "stdio.h"
#define RX_BUFFER_SIZE 9
uint8_t rx_buffer[RX_BUFFER_SIZE];
uint8_t rx_index = 0;
void USART1_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
// 打开USART1和GPIOA时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);
// 配置USART1的GPIO引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置USART1的通信参数
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
// 打开USART1
USART_Cmd(USART1, ENABLE);
}
void USART1_IRQHandler(void)
{
if (USART_GetITStatus(USART1, USART_IT_RXNE) == SET)
{
uint8_t data = USART_ReceiveData(USART1);
if (rx_index < RX_BUFFER_SIZE)
{
rx_buffer[rx_index++] = data;
}
if (rx_index == RX_BUFFER_SIZE)
{
USART_ITConfig(USART1, USART_IT_RXNE, DISABLE);
}
}
}
int main(void)
{
USART1_Init();
while (1)
{
// 发送查询指令
USART_SendData(USART1, 0xFF);
USART_SendData(USART1, 0x01);
USART_SendData(USART1, 0x86);
USART_SendData(USART1, 0x00);
USART_SendData(USART1, 0x00);
USART_SendData(USART1, 0x00);
USART_SendData(USART1, 0x00);
USART_SendData(USART1, 0x00);
USART_SendData(USART1, 0x79);
// 等待数据接收完成
rx_index = 0;
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
while (rx_index < RX_BUFFER_SIZE);
// 计算甲醛浓度
uint16_t ch2o_raw = (rx_buffer[2] << 8) | rx_buffer[3];
float ch2o_conc = ch2o_raw / 1000.0;
// 显示甲醛浓度
printf("CH2O Concentration: %.3f mg/m3\r\n", ch2o_conc);
// 等待一段时间后再进行下一次检测
delay_ms(1000);
}
}
void delay_ms(uint32_t ms)
{
uint32_t i, j;
for (i = 0; i < ms; i++)
for (j = 0; j < 2000; j++);
}
```
该程序通过USART1与Ze08甲醛传感器进行通信,每隔一段时间就发送查询指令,等待传感器返回数据并计算甲醛浓度。具体实现方法如下:
1. 在程序开头初始化USART1,将其配置为9600波特率的通信模式,并设置GPIO引脚。
2. 在程序中定义一个接收缓冲区rx_buffer和接收缓冲区的索引rx_index。
3. 在程序中添加USART1的中断处理函数USART1_IRQHandler(),用于接收数据并存储到rx_buffer数组中。
4. 在主函数中,使用USART_SendData()函数向Ze08甲醛传感器发送查询指令,并等待数据接收完成。
5. 将接收到的数据进行处理,计算甲醛浓度。
6. 通过printf()函数将甲醛浓度显示在串口终端上。
7. 在程序结尾添加delay_ms()函数,用于等待一段时间后再进行下一次检测。
需要注意的是,该程序中的USART1_IRQHandler()函数是USART1的中断处理函数,其中的代码用于接收数据并存储到rx_buffer数组中。在使用时需要在stm32f10x_it.c文件中添加中断向量表和中断处理函数。此外,在实际应用中,还需要进行一些环境因素的校准,以提高检测的准确性和可靠性。
相关推荐
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)