秒表设计与实现代码
时间: 2023-08-13 19:03:51 浏览: 43
以下是基于 Python 语言的秒表设计与实现代码:
```python
import time
def stopwatch():
start_time = time.time()
input("按下回车键开始计时,再次按下回车键停止计时。")
end_time = time.time()
elapsed_time = end_time - start_time
print("计时结果为:{:.2f}秒".format(elapsed_time))
if __name__ == "__main__":
stopwatch()
```
该代码使用了 Python 标准库中的 `time` 模块,通过 `time.time()` 函数获取当前时间戳,从而实现计时功能。程序会在用户按下回车键开始计时,再次按下回车键停止计时,并输出计时结果。
相关问题
基于VHDL的数字秒表设计方案及代码
好的,以下是一个简单的数字秒表的VHDL设计方案及代码:
```vhdl
-- 定义模块
entity stopwatch is
port (
clk: in std_logic; -- 输入时钟信号
reset: in std_logic; -- 输入复位信号
start_stop: in std_logic; -- 输入开始/停止信号
hundredths: out std_logic_vector(7 downto 0); -- 输出毫秒数
seconds: out std_logic_vector(7 downto 0); -- 输出秒数
minutes: out std_logic_vector(7 downto 0) -- 输出分钟数
);
end entity;
-- 实现模块
architecture Behavioral of stopwatch is
signal count: std_logic_vector(23 downto 0); -- 计数器
signal is_running: std_logic; -- 计时标志
signal current_hundredths: std_logic_vector(7 downto 0); -- 当前毫秒数
signal current_seconds: std_logic_vector(7 downto 0); -- 当前秒数
signal current_minutes: std_logic_vector(7 downto 0); -- 当前分钟数
begin
-- 计数器逻辑
process(clk, reset)
begin
if reset = '1' then
count <= (others => '0');
elsif rising_edge(clk) then
if is_running = '1' then
count <= count + 1;
end if;
end if;
end process;
-- 毫秒数逻辑
current_hundredths <= std_logic_vector(unsigned(count(23 downto 16)) mod 100);
-- 秒数逻辑
process(clk, reset)
begin
if reset = '1' then
current_seconds <= (others => '0');
elsif rising_edge(clk) then
if is_running = '1' then
current_seconds <= std_logic_vector(unsigned(count(15 downto 8)) mod 60);
end if;
end if;
end process;
-- 分钟数逻辑
process(clk, reset)
begin
if reset = '1' then
current_minutes <= (others => '0');
elsif rising_edge(clk) then
if is_running = '1' then
current_minutes <= std_logic_vector(unsigned(count(7 downto 0)) mod 60);
end if;
end if;
end process;
-- 输出逻辑
hundredths <= current_hundredths;
seconds <= current_seconds;
minutes <= current_minutes;
-- 开始/停止逻辑
process(start_stop)
begin
if start_stop = '1' then
is_running <= not is_running;
end if;
end process;
end Behavioral;
```
这个数字秒表模块有以下几个输入和输出:
- 输入时钟信号 `clk`
- 输入复位信号 `reset`
- 输入开始/停止信号 `start_stop`
- 输出毫秒数 `hundredths`
- 输出秒数 `seconds`
- 输出分钟数 `minutes`
在该设计中,使用了一个24位的计数器来计算总毫秒数,然后将其转换为毫秒、秒和分钟。同时,还使用一个标志 `is_running` 来表示秒表是否在运行。当 `start_stop` 信号为高电平时,该标志将翻转,从而启动或停止秒表。
请注意,这只是一个简单的数字秒表设计,您可能需要根据自己的需求进行修改和调整。
51单片机LED 数码管秒表的设计c语言代码
以下是51单片机LED数码管秒表的设计c语言代码:
```c
#include <reg52.h> // 引入51单片机头文件
sbit D1 = P2^0; // 数码管段选引脚
sbit D2 = P2^1;
sbit D3 = P2^2;
sbit D4 = P2^3;
sbit D5 = P2^4;
sbit D6 = P2^5;
sbit D7 = P2^6;
sbit D8 = P2^7;
sbit LSA = P1^0; // 数码管位选引脚
sbit LSB = P1^1;
sbit LSC = P1^2;
unsigned char code table[] = { // 数码管显示0-9的编码
0xC0, 0xF9, 0xA4, 0xB0, 0x99,
0x92, 0x82, 0xF8, 0x80, 0x90
};
void delay(unsigned int i) { // 延时函数
while(i--);
}
void main() {
unsigned int i, j; // 定义变量
unsigned char num[8] = { // 定义数组存放数码管显示的数值
0, 0, 0, 0, 0, 0, 0, 0
};
while(1) {
for(i = 0; i < 1000; i++) { // 循环1000次,即1秒钟
for(j = 0; j < 1000; j++) { // 等待1毫秒
num[0] = i / 100; // 计算百位数值
num[1] = (i % 100) / 10; // 计算十位数值
num[2] = i % 10; // 计算个位数值
num[3] = j / 100; // 计算毫秒百位数值
num[4] = (j % 100) / 10; // 计算毫秒十位数值
num[5] = j % 10; // 计算毫秒个位数值
num[6] = num[7] = 0; // 数码管留空
for(int k = 0; k < 8; k++) { // 数码管循环显示
switch(k) {
case 0: LSA = 0; LSB = 0; LSC = 0; break; // 第1位数码管
case 1: LSA = 1; LSB = 0; LSC = 0; break; // 第2位数码管
case 2: LSA = 0; LSB = 1; LSC = 0; break; // 第3位数码管
case 3: LSA = 1; LSB = 1; LSC = 0; break; // 第4位数码管
case 4: LSA = 0; LSB = 0; LSC = 1; break; // 第5位数码管
case 5: LSA = 1; LSB = 0; LSC = 1; break; // 第6位数码管
case 6: LSA = 0; LSB = 1; LSC = 1; break; // 第7位数码管
case 7: LSA = 1; LSB = 1; LSC = 1; break; // 第8位数码管
}
P0 = table[num[k]]; // 数码管显示数值
delay(100); // 延时100微秒
P0 = 0x00; // 关闭数码管
}
}
}
}
}
```
以上代码实现了一个简单的51单片机LED数码管秒表,使用定时器计算时间,循环显示数值。
相关推荐
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![](https://img-home.csdnimg.cn/images/20210720083646.png)
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)