用verilog写一个按键消抖的代码
时间: 2023-10-27 07:07:10 浏览: 42
下面是一个简单的按键消抖Verilog代码的例子:
```verilog
module debounce(
input clk, // 时钟输入
input key, // 按键输入
output reg deb_key // 消抖后的按键输出
);
reg [2:0] cnt; // 计数器
always @(posedge clk) begin
if (key != deb_key) begin
cnt <= cnt + 1; // 如果按键状态改变,计数器加1
end else begin
cnt <= 0; // 如果按键状态未改变,计数器清零
end
end
always @(posedge clk) begin
if (cnt >= 3) begin // 如果计数器值大于等于3,说明按键已经稳定
deb_key <= key; // 更新消抖后的按键状态
end
end
endmodule
```
这个代码中,我们使用了一个计数器来实现按键消抖。当按键状态改变时,计数器会加1,如果计数器值达到一定的阈值(这里是3),则说明按键已经稳定,更新消抖后的按键状态。如果按键状态未改变,则计数器清零。这个代码比较简单,但是可以有效地消除按键抖动的影响。
相关问题
使用verilog写一个按键消抖
可以的,以下是一个基本的按键消抖的verilog代码:
module debounce (
input clk,
input button,
output reg debounced_button
);
reg [1:0] state;
parameter debounce_time = 10; // 消抖时间,单位为时钟周期
always @(posedge clk) begin
case (state)
2'b00: begin
if (button) begin
state <= 2'b01;
end else begin
state <= 2'b00;
end
end
2'b01: begin
if (button) begin
state <= 2'b10;
end else begin
state <= 2'b00;
end
end
2'b10: begin
if (!button) begin
state <= 2'b11;
end else begin
state <= 2'b10;
end
end
2'b11: begin
if (!button) begin
state <= 2'b00;
debounced_button <= 1;
end else begin
state <= 2'b10;
end
end
default: begin
state <= 2'b00;
end
endcase
end
endmodule
这个代码使用了一个有限状态机来实现按键消抖,当检测到按键按下时,会进入状态1,然后等待一定时间,如果在等待时间内检测到按键松开,则进入状态3,如果等待时间内按键仍然按下,则进入状态2,等待按键松开。当检测到按键松开时,会进入状态0,然后输出debounced_button信号表示按键已经消抖。
用verilog写一个按键消抖程序
以下是一个简单的按键消抖程序的 Verilog 代码示例:
```
module debounce(
input clk,
input button,
output reg debounced_button
);
reg [3:0] count = 4'b0000;
reg last_button;
always @(posedge clk) begin
if (button != last_button) begin
count <= 4'b0000;
end else begin
if (count == 4'b1111) begin
debounced_button <= button;
end else begin
count <= count + 1;
end
end
last_button <= button;
end
endmodule
```
以上代码中,使用了一个计数器来检测按键的状态是否保持稳定,如果连续检测到 4 次相同的状态,就认为按键已经消抖完成,然后将其状态赋给输出 debounced_button。