stm32串口1接收中断
时间: 2023-09-04 21:15:15 浏览: 38
在STM32中,如果需要使用串口1进行接收中断,可以按照以下步骤进行操作:
1. 配置串口1的GPIO引脚,设置为对应的复用功能,并使能时钟。
2. 配置串口1的工作模式、波特率等相关参数,使能串口1时钟,并使能串口1。
3. 配置NVIC中断控制器,使能串口1接收中断。
4. 在中断服务函数中,判断接收数据的标志位是否被触发,如果是,则读取接收数据寄存器中的数据,并进行相应的处理。
以下是一个示例代码:
```c
//配置串口1的GPIO引脚,设置为对应的复用功能,并使能时钟
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource9, GPIO_AF_USART1);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource10, GPIO_AF_USART1);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9 | GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
//配置串口1的工作模式、波特率等相关参数,使能串口1时钟,并使能串口1
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
USART_InitTypeDef USART_InitStructure;
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
USART_Cmd(USART1, ENABLE);
//配置NVIC中断控制器,使能串口1接收中断
NVIC_InitTypeDef NVIC_InitStructure;
NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
//中断服务函数
void USART1_IRQHandler(void)
{
if(USART_GetITStatus(USART1, USART_IT_RXNE) != RESET) //判断接收数据的标志位是否被触发
{
uint8_t data = USART_ReceiveData(USART1); //读取接收数据寄存器中的数据
//进行相应的处理
}
}
```