stm32标准库定义两个按键控制四位数码管加减
时间: 2023-06-18 07:08:34 浏览: 77
好的,那我先介绍一下如何使用STM32标准库来定义按键和数码管。
首先需要在代码中引入相应的头文件,如下所示:
```c
#include "stm32f10x.h"
#include "stm32f10x_gpio.h"
#include "stm32f10x_rcc.h"
```
接着需要定义按键和数码管的引脚,可以使用GPIO宏来定义,如下所示:
```c
#define KEY1_PIN GPIO_Pin_0
#define KEY2_PIN GPIO_Pin_1
#define LED1_PIN GPIO_Pin_8
#define LED2_PIN GPIO_Pin_9
#define LED3_PIN GPIO_Pin_10
#define LED4_PIN GPIO_Pin_11
#define SEG_A_PIN GPIO_Pin_12
#define SEG_B_PIN GPIO_Pin_13
#define SEG_C_PIN GPIO_Pin_14
#define SEG_D_PIN GPIO_Pin_15
```
然后需要对引脚进行初始化,使用RCC和GPIO宏来初始化,如下所示:
```c
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = KEY1_PIN | KEY2_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = LED1_PIN | LED2_PIN | LED3_PIN | LED4_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = SEG_A_PIN | SEG_B_PIN | SEG_C_PIN | SEG_D_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOC, &GPIO_InitStructure);
```
以上代码使用了GPIOA、GPIOB和GPIOC来初始化引脚,需要根据实际情况进行修改。
接着,需要编写一个循环,用来检测按键状态和控制数码管的显示。具体代码如下:
```c
while(1)
{
if(GPIO_ReadInputDataBit(GPIOA, KEY1_PIN) == RESET)
{
// 按下KEY1,数码管加1
num++;
if(num > 9999)
num = 0;
}
if(GPIO_ReadInputDataBit(GPIOA, KEY2_PIN) == RESET)
{
// 按下KEY2,数码管减1
num--;
if(num < 0)
num = 9999;
}
// 显示num的四位数码
int temp = num % 10;
GPIO_WriteBit(GPIOC, SEG_A_PIN, temp & 0x01);
GPIO_WriteBit(GPIOC, SEG_B_PIN, (temp >> 1) & 0x01);
GPIO_WriteBit(GPIOC, SEG_C_PIN, (temp >> 2) & 0x01);
GPIO_WriteBit(GPIOC, SEG_D_PIN, (temp >> 3) & 0x01);
temp = (num / 10) % 10;
GPIO_WriteBit(GPIOB, LED1_PIN, temp & 0x01);
GPIO_WriteBit(GPIOB, LED2_PIN, (temp >> 1) & 0x01);
GPIO_WriteBit(GPIOB, LED3_PIN, (temp >> 2) & 0x01);
GPIO_WriteBit(GPIOB, LED4_PIN, (temp >> 3) & 0x01);
temp = (num / 100) % 10;
GPIO_WriteBit(GPIOC, SEG_A_PIN, temp & 0x01);
GPIO_WriteBit(GPIOC, SEG_B_PIN, (temp >> 1) & 0x01);
GPIO_WriteBit(GPIOC, SEG_C_PIN, (temp >> 2) & 0x01);
GPIO_WriteBit(GPIOC, SEG_D_PIN, (temp >> 3) & 0x01);
temp = num / 1000;
GPIO_WriteBit(GPIOC, SEG_A_PIN, temp & 0x01);
GPIO_WriteBit(GPIOC, SEG_B_PIN, (temp >> 1) & 0x01);
GPIO_WriteBit(GPIOC, SEG_C_PIN, (temp >> 2) & 0x01);
GPIO_WriteBit(GPIOC, SEG_D_PIN, (temp >> 3) & 0x01);
// 延时一段时间
for(int i=0; i<100000; i++);
}
```
以上代码中,使用了一个变量num来存储当前数码管显示的数字。当按下按键时,会改变num的值,然后根据num的值来控制数码管的显示。在代码的最后,使用一个for循环来进行延时,以便观察数码管的显示效果。
需要注意的是,以上代码仅为示例代码,具体实现方式需要根据实际情况进行修改。同时,还需要根据实际情况选择合适的GPIO引脚来进行初始化。
相关推荐
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)