基于Stm32写一个用TCS3200颜色传感器白平衡的代码、
时间: 2023-03-23 18:01:41 浏览: 185
非常感谢您的问题。我可以回答您的问题。
为了基于Stm32写一个用TCS3200颜色传感器白平衡的代码,您需要了解TCS3200颜色传感器和Stm32单片机的工作原理和相关编程知识。具体步骤如下:
1. 连接TCS3200颜色传感器和Stm32单片机。将传感器的输出引脚连接到单片机的输入引脚。
2. 在Stm32单片机上编写代码,通过读取传感器的输出信号,实现颜色检测和白平衡校准。您可以使用Stm32的开发环境进行编程,例如Keil或STM32CubeIDE。
3. 在代码中使用TCS3200颜色传感器的颜色测量功能,读取不同颜色的光线强度。根据不同颜色的光线强度计算出RGB颜色值,并进行白平衡校准。
4. 根据您的具体需求,将颜色测量结果用于控制其他设备或显示在屏幕上等。
以上是基于Stm32写一个用TCS3200颜色传感器白平衡的代码的大致步骤,希望对您有所帮助。
相关问题
基于Stm32写一个用TCS3200颜色传感器白平衡的代码
你好,以下是基于Stm32写一个用TCS3200颜色传感器白平衡的代码的参考:
```c
#include "stm32f10x.h"
#define S0_PIN GPIO_Pin_3
#define S0_PORT GPIOB
#define S1_PIN GPIO_Pin_4
#define S1_PORT GPIOB
#define S2_PIN GPIO_Pin_5
#define S2_PORT GPIOB
#define S3_PIN GPIO_Pin_6
#define S3_PORT GPIOB
#define OUT_PIN GPIO_Pin_7
#define OUT_PORT GPIOB
void delay_us(uint32_t nus)
{
uint32_t ticks = nus * (SystemCoreClock / 1000000);
while(ticks--);
}
uint16_t read_color(uint8_t color)
{
GPIO_WriteBit(S2_PORT, S2_PIN, (color >> 1) & 0x01);
GPIO_WriteBit(S3_PORT, S3_PIN, color & 0x01);
delay_us(10);
return TIM_GetCapture1(TIM3);
}
int main(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB | RCC_APB2Periph_AFIO, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_StructInit(&GPIO_InitStructure);
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Pin = S0_PIN | S1_PIN | S2_PIN | S3_PIN;
GPIO_Init(GPIOB, &GPIO_InitStructure);
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
TIM_TimeBaseStructInit(&TIM_TimeBaseStructure);
TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
TIM_TimeBaseStructure.TIM_Period = 0xFFFF;
TIM_TimeBaseStructure.TIM_Prescaler = 0;
TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure);
TIM_ICInitTypeDef TIM_ICInitStructure;
TIM_ICStructInit(&TIM_ICInitStructure);
TIM_ICInitStructure.TIM_Channel = TIM_Channel_1;
TIM_ICInitStructure.TIM_ICFilter = 0x0F;
TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising;
TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1;
TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI;
TIM_ICInit(TIM3, &TIM_ICInitStructure);
GPIO_ResetBits(S0_PORT, S0_PIN | S1_PIN);
GPIO_SetBits(S2_PORT, S2_PIN | S3_PIN);
while(1)
{
uint16_t red = read_color(0x00);
uint16_t green = read_color(0x01);
uint16_t blue = read_color(0x02);
// Calculate white balance coefficients
uint16_t red_coef = (blue << 8) / red;
uint16_t green_coef = (blue << 8) / green;
uint16_t blue_coef = 0xFF;
// Set white balance coefficients
TIM_SetCompare1(TIM3, red_coef);
delay_us(10);
TIM_SetCompare1(TIM3, green_coef);
delay_us(10);
TIM_SetCompare1(TIM3, blue
基于stm32写一个TCS3200颜色传感器白平衡的代码
可以回答这个问题。
基于STM32的TCS3200颜色传感器白平衡代码可以分为以下几个步骤:
1. 配置TCS3200传感器,包括选择输出频率和输出占空比等参数。
2. 在STM32上配置定时器,使得定时器能够产生适当的PWM信号,用于控制TCS3200传感器的输出。
3. 通过调整PWM信号的占空比和输出频率,让传感器输出适当的颜色信号。
4. 根据传感器输出的颜色信号,计算出三个通道的RGB值,然后根据这些值进行白平衡校正。
下面是一份基于STM32的TCS3200颜色传感器白平衡代码示例,仅供参考:
```c
#include "stm32f10x.h"
//定义TCS3200输出引脚
#define S2 GPIO_Pin_8
#define S3 GPIO_Pin_9
#define OUT GPIO_Pin_10
//定义RGB三个通道的引脚
#define R GPIO_Pin_11
#define G GPIO_Pin_12
#define B GPIO_Pin_13
//定义定时器2的周期
#define TIMER_PERIOD 7199
void TCS3200_Config(void)
{
//配置S2和S3引脚
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = S2 | S3;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
//配置OUT引脚
GPIO_InitStructure.GPIO_Pin = OUT;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
//设置输出频率为20%的占空比
GPIO_ResetBits(GPIOA, S2);
GPIO_SetBits(GPIOA, S3);
}
void Timer_Config(void)
{
//使能定时器2时钟
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
//定时器2配置
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
TIM_TimeBaseStructure.TIM_Period = TIMER_PERIOD;
TIM_TimeBaseStructure.TIM_Prescaler = 0;
TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
TIM_TimeBaseStructure.TIM_RepetitionCounter = 0;
TIM_TimeBaseInit(TIM2, &TIM_TimeBaseStructure);
//使能PWM输出
TIM_OCInitTypeDef TIM_OCInitStructure;
TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
TIM_OC1Init(TIM2, &TIM_OCInitStructure);
TIM_OC2Init(TIM2, &TIM_OCInitStructure);
TIM_OC3Init(TIM2, &TIM_OCInitStructure);
//设置RGB三个通道的PWM占空比为50%
TIM_SetCompare1(TIM2, TIMER_PERIOD/2);
TIM_SetCompare2(TIM2, TIMER_PERIOD/2);
TIM