stm32使用固件库串口接收程序
时间: 2023-08-02 09:06:30 浏览: 39
以下是使用STM32固件库实现串口接收的程序示例:
```c
#include "stm32f10x.h"
#include <stdio.h>
USART_InitTypeDef USART_InitStructure;
void USART1_Config(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// 使能 USART1 和 GPIOA 时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);
// USART1 TX (PA.09) 和 RX (PA.10) 引脚复用设置
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9 | GPIO_Pin_10;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// USART1 初始化设置
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
// 使能 USART1
USART_Cmd(USART1, ENABLE);
}
int main(void)
{
char ch;
// USART1 配置
USART1_Config();
while (1)
{
// 等待接收数据
while (USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == RESET);
// 读取接收数据
ch = USART_ReceiveData(USART1);
// 处理接收到的数据
printf("Received character: %c\r\n", ch);
}
}
```
首先,在主函数中调用 USART1_Config 函数进行串口初始化设置。在 while 循环中,通过 USART_GetFlagStatus 函数判断是否有数据接收到,如果有,则通过 USART_ReceiveData 函数读取数据,并进行处理。在本例中,将接收到的字符通过 printf 函数输出到串口。
相关推荐
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)