void I2C_Bus_Init(void)
时间: 2023-09-23 11:04:03 浏览: 38
这段代码定义了一个函数 `I2C_Bus_Init()`,用于初始化 I2C 总线。具体实现可能包括以下几个方面:
- 配置 I2C 硬件的寄存器或者调用相关库函数,以使 I2C 总线能够正常工作。
- 初始化 I2C 总线的参数,例如时钟速率、从设备地址、传输模式等。
- 配置相关的中断或者 DMA,以便在数据传输过程中能够及时响应和处理相关事件。
- 如果有必要,进行总线扫描,以检测当前连接在 I2C 总线上的从设备,并进行相应的初始化和配置。
需要根据具体的应用场景和硬件平台进行调整和优化。
相关问题
重构以下代码 void i2c_as_slave_xfer_enable(int bus) { u32 ctrl_bits; /* Disable Master function , Set buffer page selection = 0*/ ctrl_bits = i2c_as_read_reg(bus,I2C_FUNCTION_CONTROL_REG); ctrl_bits &= ~( ENABLE_MASTER_FUNC); ctrl_bits |= ENABLE_SLAVE_FUNC; #if defined(GROUP_AST2300_PLUS) ctrl_bits &= ~( BUFFER_SELECTION_PAGE_MASK); ctrl_bits |= BUFFER_SELECTION_PAGE_0; #endif i2c_as_write_reg( bus,ctrl_bits,I2C_FUNCTION_CONTROL_REG); udelay(100); /* clear interrups */ i2c_as_disable_all_interrupts(bus); i2c_as_write_reg (bus, CLR_ALL_INTS_VAL, I2C_INTR_STATUS_REG); as_data_ptr[bus].SlaveTX_Enable = 1; as_data_ptr[bus].TX_len = 0; as_data_ptr[bus].TX_index = 0; as_data_ptr[bus].MasterRX_len = 0; as_data_ptr[bus].MasterRX_index = 0; /* Default I2C_BYTE_MODE for GROUP_AST2300 and GROUP_AST2300_PLUS. For testing buffer transfer mode of SSIF, init ssif tx pool buffer. */ //as_data_ptr[bus].pool_buff_base = AST_I2C_POLLBUF_VA_BASE; /* Enable interrupts */ i2c_as_write_reg (bus, ENABLE_TX_DONE_WITH_ACK_INTR | \ ENABLE_TX_DONE_WITH_NACK_INTR | \ ENABLE_RX_DONE_INTR| ENABLE_STOP_CONDITION_RECVD_INTR| ENABLE_ABNORMAL_START_STOP_RECVD_INTR| ENABLE_SLAVE_ADDR_MATCH_INTR, I2C_INTR_CONTROL_REG); }
重构代码:
```
void i2c_as_slave_xfer_enable(int bus) {
u32 ctrl_bits;
// 禁用主机功能,设置缓冲区页面选择为0
ctrl_bits = i2c_as_read_reg(bus, I2C_FUNCTION_CONTROL_REG);
//...
}
```
其中该代码禁用了I2C总线上的主机功能,并将缓冲区页面选择设置为0。
GD32硬件I2C代码
你好!以下是一个简单的GD32硬件I2C的代码示例:
```c
#include "gd32f10x.h"
#include <stdio.h>
#define I2C0_SLAVE_ADDRESS7 0x82
void i2c_config(void)
{
/* Enable I2C0 clock */
rcu_periph_clock_enable(RCU_I2C0);
/* I2C0 GPIO ports */
gpio_init(GPIOB, GPIO_MODE_AF_OD, GPIO_OSPEED_50MHZ, GPIO_PIN_6 | GPIO_PIN_7);
gpio_af_set(GPIOB, GPIO_AF_1, GPIO_PIN_6 | GPIO_PIN_7);
/* I2C0 parameter configuration */
i2c_clock_config(I2C0, 100000, I2C_DTCY_2);
i2c_mode_addr_config(I2C0, I2C_I2CMODE_ENABLE, I2C_ADDFORMAT_7BITS, I2C0_SLAVE_ADDRESS7);
i2c_ack_config(I2C0, I2C_ACK_ENABLE);
i2c_enable(I2C0);
}
void i2c_write_data(uint8_t data)
{
/* Wait until I2C bus is idle */
while(i2c_flag_get(I2C0, I2C_FLAG_I2CBSY));
/* Send the byte to be written */
i2c_data_transmit(I2C0, data);
/* Wait until the transmission finishes */
while(!i2c_flag_get(I2C0, I2C_FLAG_I2CTC));
/* Clear the transmission flag */
i2c_flag_clear(I2C0, I2C_FLAG_I2CTC);
}
uint8_t i2c_read_data(void)
{
uint8_t data;
/* Wait until the I2C bus is idle */
while(i2c_flag_get(I2C0, I2C_FLAG_I2CBSY));
/* Enable I2C0 acknowledge */
i2c_ack_config(I2C0, I2C_ACK_ENABLE);
/* Enable I2C0 receive data */
i2c_receive_config(I2C0, I2C_RECEIVE_ENABLE);
/* Wait until the byte is received */
while(!i2c_flag_get(I2C0, I2C_FLAG_RBNE));
/* Read the received data */
data = i2c_data_receive(I2C0);
/* Clear the receive flag */
i2c_flag_clear(I2C0, I2C_FLAG_RBNE);
return data;
}
int main(void)
{
/* Configure I2C0 */
i2c_config();
/* Write data to the slave device */
i2c_write_data(0xAA);
/* Read data from the slave device */
uint8_t data = i2c_read_data();
/* Print the received data */
printf("Received data: 0x%02X\n", data);
while(1);
}
```
这段代码使用了GD32库函数来配置和操作GD32的I2C接口。它包括了初始化I2C接口、向从设备写入数据、从从设备读取数据,并通过串口打印接收到的数据。请注意,这只是一个简单的示例,实际使用中可能需要根据具体的硬件和应用进行适当的修改和调整。
希望对你有帮助!如有其他问题,请随时提问。