8位数码管显示学号程序
时间: 2024-02-11 15:05:52 浏览: 19
好的,以下是一份基于Arduino的8位数码管显示学号的程序示例:
```C++
#include <TM1637Display.h>
// Set up the TM1637 display module
#define CLK 2
#define DIO 3
TM1637Display display(CLK, DIO);
void setup() {
// Initialize the display module
display.setBrightness(0x0f);
// Display the student ID on the 8-digit LED display
display.showNumberDec(12345678);
}
void loop() {
// Nothing to do here, the student ID will remain displayed on the module
}
```
注意,这份示例程序假设你已经将8位数码管连接到了Arduino的对应引脚上。如果你还没有这样做,你需要先阅读一下你的数码管模块的说明文档,以了解正确的连接方式。
相关问题
C语言8位数码管显示学号程序
以下是一个简单的C语言程序,用于在8位数码管上显示一个学号(例如:20210001):
```c
#include <reg52.h> // 引入51单片机头文件
#define uint unsigned int // 定义uint为无符号整型
// 定义数码管码表
unsigned char code table[] = {
0x3F, 0x06, 0x5B, 0x4F, 0x66,
0x6D, 0x7D, 0x07, 0x7F, 0x6F
};
void delay(uint i) { // 延时函数
while (i--);
}
void main() {
unsigned int num = 20210001; // 学号
unsigned char i;
unsigned char display[8]; // 数码管显示数组
// 将学号拆分成每一位数字,并存入数组中
for (i = 0; i < 8; i++) {
display[i] = num % 10;
num /= 10;
}
// 数码管循环扫描显示
while (1) {
for (i = 0; i < 8; i++) {
P0 = table[display[i]]; // 显示数字
P2 = 1 << i; // 选择位
delay(100); // 延时一段时间
P2 = 0x00; // 关闭所有位
}
}
}
```
注意,这个程序使用了51单片机的IO口来控制8位数码管的显示。如果你使用的是其他硬件平台,可能需要修改对应的代码。
利用LPC2103芯片C语言8位数码管显示学号程序
以下是一个基于LPC2103芯片,使用C语言编写的8位数码管显示学号的程序示例:
```c
#include <LPC210x.H>
#define LED_PORT 0x000000FF // port 0.0-0.7
unsigned char num[8] = {1, 3, 0, 2, 2, 9, 0, 5}; // 学号
void delay_ms(unsigned int count) {
unsigned int i, j;
for(i = 0; i < count; i++) {
for(j = 0; j < 6000; j++);
}
}
void display(unsigned char data) {
IO0SET = LED_PORT; // 设置为高电平
IO0CLR = (1<<data); // 设置要显示的数码管为低电平
}
int main(void) {
unsigned char i = 0;
PINSEL0 = 0; // 设置为GPIO模式
IO0DIR = LED_PORT; // 设置为输出模式
while(1) {
display(i);
delay_ms(1000); // 延时1秒
i++;
if(i > 7) i = 0;
}
return 0;
}
```
该程序的主要功能是将学号“13022905”循环显示在8位数码管上。其中,使用了delay_ms()函数实现延时功能,display()函数用于控制数码管的显示。具体实现方法为,将8位数码管所在的8个引脚设置为输出模式,然后依次将要显示的数码管引脚设置为低电平,其余引脚设置为高电平,从而实现数码管的控制。