SLAS074D − DECEMBER 1986 − REVISED SEPTEMBER 2003
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted
(1)
UNIT
Supply voltage (V
CC+
with respect to V
CC−
) 15 V
Analog input voltage (IN− or IN+) V
CC−
to V
CC+
Reference voltage range V
CC−
to V
CC+
Clock input voltage range 0 V to V
CC+
Operating free-air temperature range, T
A
0°C to 70°C
Storage temperature range, T
stg
−65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: N package 260°C
(1)
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
MIN NOM MAX UNIT
Supply voltage, V
CC+
4 5 6 V
Supply voltage, V
CC−
−3 −5 −8 V
Reference voltage, V
ref
1 V
High-level input voltage, CLK, RUN/HOLD, V
IH
2.8 V
Low-level input voltage, CLK, RUN/HOLD, V
IL
0.8 V
Differential input voltage, V
ID
V
CC−
+1 V
CC+
−0.5 V
Maximum operating frequency, f
clock
(see Note 1) 1.2 2 MHz
Operating free-air temperature range, T
A
0 70 °C
NOTE 1: Clock frequency range extends down to 0 Hz.
ELECTRICAL CHARACTERISTICS
V
CC+
= 5 V, V
CC−
= 5 V, V
ref
= 1 V, f
clock
= 120 kHz, T
A
= 25°C (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
High-level output voltage
D1-D5,B1,B2,B4,B8 I
O
= −1 mA 2.4 5
V
OH
High-level output voltage
Other outputs
I
O
= −10 µA 4.9 5
V
V
OL
Low-level output voltage I
O
= 1.6 mA 0.4 V
V
ON(PP)
Peak-to-peak output noise voltage (see Note 1) V
ID
= 0, Full scale = 2 V 15 µV
α
VO
Zero-reading temperature coefficient of output voltage V
ID
= 0, 0°C ≤ T
A
≤ 70°C 0.5 2 µV/°C
I
IH
High-level input current V
I
= 5 V, 0°C ≤ T
A
≤ 70°C 0.1 10 µA
I
IL
Low-level input current V
I
= 0 V, 0°C ≤ T
A
≤ 70°C −0.02 −0.1 mA
Input leakage current, IN− and IN+
T
A
= 25°C 1 10
I
I
Input leakage current, IN− and IN+ V
ID
= 0
0°C ≤ T
A
≤ 70°C 250
pA
T
A
= 25°C 1 2
I
CC+
Positive supply current f
clock
= 0
0°C ≤ T
A
≤ 70°C 3
mA
T
A
= 25°C −0.8 −2
I
CC−
Negative supply current f
clock
= 0
0°C ≤ T
A
≤ 70°C −3
mA
C
pd
Power dissipation capacitance See Note 2 40 pF
NOTES: 1. This is the peak-to-peak value that is not exceeded 95% of the time.
2. Factor-relating clock frequency to increase in supply current. At V
CC+
= 5 V, I
CC+
= I
CC+
(f
clock
= 0) + C
pd
× 5 V × f
clock