"Hypertherm软件操作手册V9.75.0使用指南及注意事项"

需积分: 0 6 浏览量更新于2024-03-22 收藏 15.83MB PDF 举报

The Hypertherm software user manual provides comprehensive guidance and support for operators utilizing Hypertherm's cutting-edge technologies. Copyrighted in 2013 by Hypertherm Inc., the manual covers a wide range of features including ArcGlide, COMMAND, EDGE Pro, EDGE Pro Ti, HPR, HSD, HyIntensity Fiber Laser, Hypernest, Hypernet, Hypertherm, HyPrecision, MAXPRO, MicroEDGE Pro, Phoenix, Powermax, and Sensor. As a trusted leader in the industry, Hypertherm's software is designed to optimize efficiency and precision in plasma cutting operations. With a focus on user-friendly interfaces and advanced functionalities, Hypertherm software enables operators to enhance productivity and achieve high-quality results. The manual also highlights the compatibility of Hypertherm software with Microsoft technologies such as Windows, ensuring seamless integration and reliable performance. By utilizing the Hypertherm software user manual, operators can harness the full potential of cutting-edge technologies to elevate their workflow and achieve superior cutting outcomes.

SC-16 Safety and Compliance

Safety

TOXIC FUMES CAN CAUSE INJURY OR DEATH

The plasma arc by itself is the heat source used for

cutting. Accordingly, although the plasma arc has not

been identified as a source of toxic fumes, the material

being cut can be a source of toxic fumes or gases that

deplete oxygen.

Fumes produced vary depending on the metal that is

cut. Metals that may release toxic fumes include, but are

not limited to, stainless steel, carbon steel, zinc

(galvanized), and copper.

In some cases, the metal may be coated with a

substance that could release toxic fumes. Toxic coatings

include, but are not limited to, lead (in some paints),

cadmium (in some paints and fillers), and beryllium.

Gases produced by plasma cutting vary based on the

material to be cut and the method of cutting, but may

include ozone, oxides of nitrogen, hexavalent chromium,

hydrogen, and other substances if such are contained in

or released by the material being cut.

Caution should be taken to minimize exposure to fumes

produced by any industrial process. Depending upon

the chemical composition and concentration of the

fumes (as well as other factors, such as ventilation),

there may be a risk of physical illness, such as birth

defects or cancer.

It is the responsibility of the equipment and site owner

to test the air quality in the area where the equipment is

used and to ensure that the air quality in the workplace

meets all local and national standards and regulations.

The air quality level in any relevant workplace depends

on site-specific variables such as:

• Table design (wet, dry, underwater).

• Material composition, surface finish, and composition

of coatings.

• Volume of material removed.

• Duration of cutting or gouging.

• Size, air volume, ventilation and filtration of the work

area.

• Personal protective equipment.

• Number of welding and cutting systems in operation.

• Other site processes that may produce fumes.

If the workplace must conform to national or local

regulations, only monitoring or testing done at the site

can determine whether the site is above or below

allowable levels.

To reduce the risk of exposure to fumes:

• Remove all coatings and solvents from the metal

before cutting.

• Use local exhaust ventilation to remove fumes from

the air.

• Do not inhale fumes. Wear an air-supplied respirator

when cutting any metal coated with, containing, or

suspected to contain toxic elements.

• Assure that those using welding or cutting

equipment, as well as air-supplied respiration

devices, are qualified and trained in the proper use of

such equipment.

• Never cut containers with potentially toxic materials

inside. Empty and properly clean the container first.

• Monitor or test the air quality at the site as needed.

• Consult with a local expert to implement a site plan

to ensure safe air quality.

SC-20 Safety and Compliance

Safety

PACEMAKER AND HEARING AID OPERATION

Pacemaker and hearing aid operation can be affected

by magnetic fields from high currents.

Pacemaker and hearing aid wearers should consult a

doctor before going near any plasma arc cutting and

gouging operations.

To reduce magnetic field hazards:

• Keep both the work cable and the torch lead to one

side, away from your body.

• Route the torch leads as close as possible to the

work cable.

• Do not wrap or drape the torch lead or work cable

around your body.

• Keep as far away from the power supply as possible.

NOISE CAN DAMAGE HEARING

Cutting with a plasma arc can exceed acceptable noise

levels as defined by local codes in many applications.

Prolonged exposure to excessive noise can damage

hearing. Always wear proper ear protection when

cutting or gouging, unless sound pressure level

measurements taken at the installed site have verified

personal hearing protection is not necessary per

relevant international, regional, and local codes.

Significant noise reduction can be obtained by adding

simple engineering controls to cutting tables such as

barriers or curtains positioned between the plasma arc

and the workstation; and/or locating the workstation

away from the plasma arc. Implement administrative

controls in the workplace to restrict access, limit

operator exposure time, screen off noisy working areas

and/or take measures to reduce reverberation in

working areas by putting up noise absorbers.

Use ear protectors if the noise is disruptive or if there is

a risk of hearing damage after all other engineering and

administrative controls have been implemented. If

hearing protection is required, wear only approved

personal protective devices such as ear muffs or ear

plugs with a noise reduction rating appropriate for the

situation. Warn others in the area of possible noise

hazards. In addition, ear protection can prevent hot

splatter from entering the ear.

A PLASMA ARC CAN DAMAGE FROZEN PIPES

Frozen pipes may be damaged or can burst if you attempt to thaw them with a plasma torch.

剩余660页未读，继续阅读

地图帝

粉丝: 25
资源: 297

"Hypertherm软件操作手册V9.75.0使用指南及注意事项"

软件使用帮助手册1

软件使用手册1

docs：Hypertherm产品的文档和图像

Phoenix Software V9 Series 程序员参考手册1

美国海宝凤凰数控系统完整技术手册，原版。海宝原著。

Phoenix Software V9.76.0 操作手册 修订版本 10 (简体中文 Simplified Chinese)

Hypertherm Phoenix Software V9.76.0 (10版) 中文操作手册

Hypertherm火焰切割机操作与安装指南

Hypertherm PM65/85等离子切割系统操作与注册指南

ProNest 2010中文用户手册：高效排样与切割指南

最新资源

Phoenix Software V9.76.0 操作手册修订版本 10 (简体中文 Simplified Chinese)