DS2100N/DS2400N用户手册（2017版）

需积分: 50 196 浏览量更新于2024-07-15 收藏 10.8MB PDF 举报

本资源为《DS2100N/DS2400N参考手册》,由Datalogic S.r.l.出版，发行日期为2017年7月，版权属于Datalogic S.p.A.及其关联公司。这是一份详尽的技术文档，包含了DS2100N和DS2400N系列条形码扫描器的产品信息、规格、功能描述、安装指南、操作说明以及安全与合规性指导。在手册的开始部分，着重于版权声明，强调未经Datalogic书面许可，任何形式的复制、存储或传播该文档的行为都是违法的。此外，手册提到了Datalogic拥有的商标，如Datalogic、Genius、Subzero、ACR和X-PRESS，以及其他第三方品牌的权利归属。手册的主要内容包括： 1. **参考文档**：这部分提供了关于DS2100N和DS2400N扫描器的详细技术参考，包括硬件组件、接口规格、性能指标、光学特性等，是用户理解和操作设备的基础。 2. **约定**：介绍了文档中使用的符号、术语和约定，以确保全球读者能准确理解文档中的信息。 3. **通过网站获取支持**：手册指出了用户可以通过Datalogic的官方网站获取进一步的技术支持、软件更新、故障排除指南和其他相关资源。 4. **专利**：概述了DS2100N/DS2400N所涉及的专利信息，表明这些产品是技术创新的体现，并可能受到法律保护。 5. **安全和合规性**：这部分关注设备的安全操作规范，以及可能需要遵守的行业标准和法规，以确保用户的使用符合法律要求和最佳实践。 6. **目录**：手册的其余部分按照逻辑顺序排列，列出了各个章节的主题，方便用户快速查找所需的信息。这份文档对于DS2100N和DS2400N的用户、技术人员和维护人员来说是极其重要的，它不仅提供了产品的详细规格，还为日常操作和故障解决提供了实用指导。由于文档涵盖了广泛的技术细节，阅读者应具备一定的计算机视觉背景知识以便充分理解其中的概念和技术应用。

DS2100N/DS2400N REFERENCE MANUAL

CBX100/500 Pinout

The table below gives the pinout of the CBX100/500 terminal block connectors. Use this

pinout when the scanner reader is connected by means of the CBX100/500:

CBX100/500 Terminal Block Connectors

Input Power

Outputs

Vdc

Power Supply Input Voltage +

Power Source - Outputs

GND

Power Supply Input Voltage -

-V

Power Reference - Outputs

Earth

Protection Earth Ground

O1+

Output 1 +

O1-

Output 1 -

Inputs

O2+

Output 2 +

Power Source – External Trigger

O2-

Output 2 -

I1A

External Trigger A (polarity insensitive)

Auxiliary Interface

I1B

External Trigger B (polarity insensitive)

Auxiliary Interface TX

-V

Power Reference – External Trigger

Auxiliary Interface RX

Power Source – Inputs

SGND

Auxiliary Interface Reference

I2A

Input 2 A (polarity insensitive)

ID-NET™

I2B

Input 2 B (polarity insensitive)

REF

Network Reference

-V

Power Reference – Inputs

ID+

ID-NET™ network +

Shield

ID-

ID-NET™ network -

Shield

Network Cable Shield

Main Interface

RS232

RS485 Full-Duplex

RS485 Half-Duplex

TX+

RTX+

RTS

TX-

RTX-

*RX+

CTS

*RX-

SGND

* Do not leave floating, see par. 4.2.2 for connection details.

CAUTION: Do not connect GND, SGND and REF to different (external)

ground references. GND, SGND and REF are internally connected through

filtering circuitry which can be permanently damaged if subjected to voltage

drops over 0.8 Vdc.

DS2100N/DS2400N REFERENCE MANUAL

STEP 3 – X-PRESS™ CONFIGURATION

X-PRESS™ is the intuitive Human Machine Interface designed to improve ease of

installation and maintenance.

Status and diagnostic information are clearly presented by means of the five colored LEDs,

whereas the single push button gives immediate access to the following relevant functions:

 AutoSetup to self-optimize and auto-configure

reading performance in demanding applications

 AutoLearn to self-detect and auto-configure for

reading unknown barcodes (by type and length)

 Test Mode with bar-graph visualization to check

static reading performance

NOTE: If using the OM2000N accessory, when entering the X-PRESS™

interface, the Oscillating Mirror remains in the default fixed position (-15°) in

order to make barcode reading easier while performing the X-PRESS™

functions.

The colors and meaning of the five LEDs are illustrated in the following table:

READY (green)

This LED indicates the device is ready to operate. For Subzero models

this LED blinks during the warm-up phase.

GOOD (green)

This LED confirms successful reading.

TRIGGER (yellow)

This LED indicates the status of the reading phase. *

COM (yellow)

This LED indicates active communication on main serial port. **

STATUS (red)

This LED indicates a NO READ result.

* In On-Line mode the TRIGGER LED corresponds to the active reading phase signaled by the Presence Sensor.

In Automatic and Continuous modes the TRIGGER LED is always on indicating that the reader is ready to read a

code.

** When connected to a Fieldbus network through the CBX500, the COM LED is always active, even in the

absence of data transmission, because of polling activity on the Fieldbus network.

During the reader startup (reset or restart phase), all the LEDs blink for one second.

PWR (blue)

This LED indicates that the reader is connected to the power supply.

(This LED is located next to the cable on Serial models).

ETH (yellow)

This LED indicates connection to the on-board Ethernet or Profinet-IO

network.

READY

GOOD

TRIGGER

COM

STATUS

SETUP

LEARN

TEST

ETH

PWR

DS2100N/DS2400N REFERENCE MANUAL

Auto Setup (Optional)

At the end of the Auto Learn procedure, you have the possibility to follow the Auto Setup

procedure to set up the reading parameters.

1. Enter the Auto Setup function by holding the X-PRESS™ push button pressed until the

SETUP LED is on.

2. Release the button to enter the Auto Setup function.

3. Once entered, if a barcode label is positioned in front of the scanline, the scanner

automatically performs the optimal setup of the reading parameters for that specific

barcode.

SETUP

LEARN

TEST

green

yellow

red

READY

GOOD

TRIGGER

COM

STATUS

Figure 6 – X-PRESS™ Interface: Auto Setup Function

The procedure is as follows:

A) place the desired barcode on

the scanline.

B) enter the AutoSetup function

(the laser turns on and the

SETUP LED blinks to indicate

the ongoing process)

C) wait until the SETUP LED

stays steady on (indicating the

reader has detected the

barcode)

This procedure ends either when the barcode is successfully decoded or after a timeout of

about 7 (seven) seconds.

The scanner will restart at the end of the process, and then the optimized reading

parameters for that barcode are automatically configured in scanner memory.

NOTE: If your application has been configured using X-PRESS™, go to

STEP 5.

Reset Scanner to Factory Default (Optional)

If it ever becomes necessary to reset the scanner to the factory default values, you can

perform this by holding the X-PRESS™ push-button pressed while powering up the scanner

and waiting for all LEDs to blink simultaneously three times before releasing the push button.

This procedure takes ≈ 5-6 seconds for Serial Models, ≈ 10 seconds for Ethernet Models, ≈

20 seconds for Profinet-IO models. At the end of the procedure the Configuration and

Environmental parameters are reset. If connected through a CBX500 with display module,

the message "Default Set" is shown on the display.

剩余129页未读，继续阅读

weixin_40901527

粉丝: 0
资源: 5

DS2100N/DS2400N用户手册（2017版）

得利捷DS2100N扫码枪中文手册

得利捷DS2100N激光条形码阅读器.pdf

DS2100串口得利捷扫码器配置软件及参数

Datalogic_DS2100N的资料

DS2100系列说明书.doc

DS2100操作

Genius入门手册.pdf

得利捷H. QL快速接线器介绍.pdf

Genius入门指南：V1.0 DS2100N调试教程

Datalogic DS2100N自动识别条码阅读器快速参考指南

最新资源