JEDEC固态技术协会发布UFS 2.2版本标准

需积分: 5 23 浏览量更新于2024-07-03 收藏 4.33MB PDF 举报

身份认证购VIP最低享 7 折!

领优惠券(最高得80元）

资源详情

资源推荐

JEDEC Standard No. 220C-2.2

-xii-

JEDEC Standard No. 220C-2.2

Page 1

UNIVERSAL FLASH STORAGE (UFS), 2.2

(From JEDEC Board Ballot JCB-20-27, formulated under the cognizance of the JC-64.1 Subcommittee

on Electrical Specifications and Command Protocols, Item 138.88)

1 SCOPE

This standard specifies the characteristics of the UFS electrical interface and the memory device. Such

characteristics include (among others) low power consumption, high data throughput, low

electromagnetic interference and optimization for mass memory subsystem efficiency. The UFS electrical

interface is based on an advanced differential interface by MIPI M-PHY specification which together with

the MIPI UniPro specification forms the interconnect of the UFS interface. The architectural model is

referencing the INCITS T10 (SCSI) SAM standard and the command protocol is based on INCITS T10

(SCSI) SPC and SBC standards.

2 NORMATIVE REFERENCE

The following normative documents contain provisions that, through reference in this text, constitute

provisions of this standard. For dated references, subsequent amendments to, or revisions of, any of these

publications do not apply. However, parties to agreements based on this standard are encouraged to

investigate the possibility of applying the most recent editions of the normative documents indicated. For

undated references, the latest edition of the normative document referred to applies.

[MIPI-M-PHY], MIPI Alliance Specification for M-PHY

, Version 3.00.00

[MIPI-UniPro], MIPI Alliance Specification for Unified Protocol (UniPro

), Version 1.6.00

[MIPI-DDB], MIPI Alliance Specification for Device Descriptor Block (DDB), Version 1.0

[SAM], INCITS T10 draft standard: SCSI Architecture Model – 5 (SAM–5), Revision 05, 19 May 2010

[SPC], INCITS T10 draft standard: SCSI Primary Commands – 4 (SPC-4), Revision 27, 11 October 2010

[SBC], INCITS T10 draft standard: SCSI Block Commands – 3 (SBC–3), Revision 24, 05 August 2010

[JESD8-12A], 1.2 V +/- 0.1V (Normal Range) and 0.8 - 1.3 V (Wide Range) Power Supply Voltage and

Interface Standard for Nonterminated Digital Integrated Circuits

[HBM-MM], JEDEC Recommended ESD Target Levels for HBM/MM Qualification, JEP155A.01,

March 2012

[CDM], JEDEC Recommended ESD-CDM Target Levels, JEP157, October 2009

[HMAC-SHA], Eastlake, D. and T. Hansen, US Secure Hash Algorithms (SHA and HMAC-SHA), RFC

4634, July 2006.

JEDEC Standard No. 220C-2.2

Page 2

3 TERMS AND DEFINITIONS

For the purposes of this standard, the terms and definitions given in the document included in clause 2,

Normative Reference, and the following apply.

Application Client: An entity that is the source of SCSI commands and task management function

requests in the host.

Byte: An 8‐bit data value with most significant bit labeled as bit 7 and least significant bit as bit 0.

Command Descriptor Block: The structure used to communicate commands from an application client

to a device server. A CDB may have a fixed length of up to 16 bytes or a variable length of between 12

and 260 bytes.

Device ID: The bus address of a UFS device.

Device Server: An entity in the device that processes SCSI commands and task management functions.

Doubleword: A 32‐bit data value with most significant bit labeled as bit 31 and least significant bit as bit

Dword: 32‐bit data value, a Doubleword.

Gigabyte: 1,073,741,824 or 2

bytes.

Host: An entity or a device with the characteristics of a primary computing device that includes one or

more SCSI initiator devices.

Initiator device: Within a transaction, the originator of a SCSI command request message to a target

device.

Kilobyte: 1024 or 2

bytes.

Logical Unit: A logical unit is an internal entity of a bus device that performs a certain function or

addresses a particular space or configuration within a bus device.

Logical Unit Number: A numeric value that identifies a logical unit within a device

Megabyte: 1,048,576 or 2

bytes.

Quadword: A 64‐bit data value with most significant bit labeled as bit 63 and least significant bit as 0.

Segment: A specified number of sequentially addressed bytes representing a data structure or section of

a data structure.

Segment ID: A 16‐bit value that represents an index into a table or an address of a segment descriptor or

simply an absolute value that is an element of an absolute address

SCSI Request Block: A data packet that contains a multi‐byte SCSI command and additional contextual

information needed to carry out the command operation. A SCSI Request Block is built by the host and is

targeted at a particular bus device.

Target device: Within a transaction, the recipient of a SCSI command request message from an initiator

device.

Task: A task is a SCSI command which includes all transactions to complete all data transfers and a

status response that will satisfy the requirements of the requested services of the command.

Transaction: A UFS primitive action which results in transmission of serial data packets between a

target device and initiator device.

JEDEC Standard No. 220C-2.2

Page 4

3.1 Acronyms (cont’d)

SBC

SCSI Block Commands

SID

Segment ID

SDU

Service Data Unit

SPC

SCSI Primary Commands

Terabyte

T_PDU

MIPI Unipro Protocol Data Unit

T_SDU

MIPI Unipro protocol Service Data Unit

UFS

Universal Flash Storage

UMPC

Ultra-Mobile PC

UniPro

Unified Protocol

UPIU

UFS Protocol Information Unit

UTP

UFS Transport Protocol

3.2 Conventions

This standard follows some conventions used in SCSI documents since it adopts several SCSI standards.

A binary number is represented in this standard by any sequence of digits consisting of only the Western-

Arabic numerals 0 and 1 immediately followed by a lower-case b (e.g., 0101b). Spaces may be included

in binary number representations to increase readability or delineate field boundaries (e.g., 0 0101 1010b).

A hexadecimal number is represented in this standard by any sequence of digits consisting of only the

Western-Arabic numerals 0 through 9 and/or the upper-case English letters A through F immediately

followed by a lower-case h (e.g., FA23h). Spaces may be included in hexadecimal number representations

to increase readability or delineate field boundaries (e.g., B FD8C FA23h).

A decimal number is represented in this standard by any sequence of digits consisting of only the

Western-Arabic numerals 0 through 9 not immediately followed by a lower-case b or lower-case h (e.g.,

25).

A range of numeric values is represented in this standard in the form "a to z", where a is the first value

included in the range, all values between a and z are included in the range, and z is the last value included

in the range (e.g., the representation "0h to 3h" includes the values 0h, 1h, 2h, and 3h).

When the value of the bit or field is not relevant, x or xx appears in place of a specific value.

The first letter of the name of a Flag is a lower-case f (e.g., fMyFlag).

The first letter of the name of a parameter included in a Descriptor or the first letter of the name of an

Attribute is:

 a lower-case b if the parameter or the Attribute size is one byte (e.g., bMyParameter),

 a lower-case w if the parameter or the Attribute size is two bytes (e.g., wMyParameter),

 a lower-case d if the parameter or the Attribute size is four bytes (e.g., dMyParameter),

 a lower-case q if the parameter or the Attribute size is eight bytes (e.g., qMyParameter).

剩余395页未读，继续阅读

drkshcn

粉丝: 1
资源: 29

JEDEC固态技术协会发布UFS 2.2版本标准

JESD220C-2_2-ufs v2.2.pdf

Universal Flash Storage (UFS) Version 2.2 JESD220C-2-2.pdf

jesd209-4b_lpddr4

jesd209-4b_low power double data rate 4 (lpddr4) .pdf

jesd209-5_4_3 lpddr5 lpddr4 lpddr3精解

jesd220e-ufs3.1_2020.jan.pdf下载

jesd79-4a和4b的区别

jesd79-3f_ddr3 中文注释解读 v3.pdf

jesd79-4c下载

ufs_v2.1_jesd220c.pdf

jesd79-3f 下载

jesd51-2中文版

jesd79-4d csdn

jesd79-4b中文

jesd79-5b 下载

jesd79-4下载

jesd79-5下载 pdf

jesd82-31a

jesd209-3c

JEDEC JESD22-B103内容

最新资源