"Sony EH6300相机手册：功能、操作、注意事项详解！"

SONY

需积分: 9 34 浏览量更新于2024-03-16 收藏 2.54MB PDF 举报

身份认证购VIP最低享 7 折!

领优惠券(最高得80元）

资源详情

资源推荐

Basic Functions

FCB-EH6300(GB) A-E23-100-15(1)

Noise Reduction

The NR (Noise Reduction) function removes noise

(both random and non-random) to provide clearer

images.

This function has six steps: levels 1 to 5, plus off.

The NR effect is applied in levels based on the gain,

and this setting value determines the limit of the effect.

In bright conditions, changing the NR level will not

have an effect.

High Sensitivity Mode

In this mode, higher sensitivity gain is applied as

standard gain increases, reaching a gain level at MAX

gain of up to 4x the standard gain. In such cases,

however, there will be a high volume noise in the

image.

Custom Gamma Mode

Gamma correction can be changed in this mode. The

following five options are available.

0: Standard

1: Straight gamma

2: S-curve - Low

3: S-curve - Mid

4: S-curve - High

Tip

Blocked-up shadows in images will be more noticeable

than usual.

Color Enhancement

A captured color image is converted to 256 levels of

gray, and you can set a color to all levels brighter than

the threshold value, and another color to all levels

darker than the threshold value.

Color specifications

• You can select from nine colors to specify for the

high-intensity and low-intensity colors.

Color options: Yellow, cyan, green, white, magenta,

red, blue, black, gray

• The default settings for color specification are “green”

for high-intensity and “white” for low-intensity.

The wide dynamic range mode includes the following

operation modes.

• WD Mode

This mode corrects blocked-up shadows and blown-

out highlights in accordance with the intensity

difference.

• WD Auto ON/OFF Mode

This mode switches WD ON/OFF automatically in

accordance with the intensity difference of the subject.

Configure the sensitivity for when WD is switched

from OFF to ON with the detection sensitivity

parameter.

• Exposure Ratio Mode

This mode fixes the shutter speed of a long exposure.

Configure the shutter speed of a short exposure by

setting the ratio with regards to a long exposure with

the exposure ratio parameter.

Blown-out highlight correction is not performed in

this mode.

• Histogram Mode

This mode uses a histogram to correct blocked-up

shadows and blown-out highlights. (The operation is

similar to that of FCB-EX1010/P Dver.)

• About WD Set Parameter

(Command: 8x 01 04 2D 0p 0q 0r 0s 0t 0u 00 00 FF)

p: Screen display (0: Combined image, 2: Long-time,

3: Short-time)

Set the screen display to the combined image, a

long exposure image or short exposure image.

q: Detection sensitivity (0: Low, 1: Mid, 2: Hi)

Select from three levels for detecting the

intensity within the image for when switching

Auto WD from OFF to ON.

r: Blocked-up shadow correction level can be

set to one of four levels. (0:L 1:M 2:H 3:S)

s: Blown-out highlight correction level can be

set to one of three levels. (0:L 1:M 2:H)

tu: Parameter to use in the exposure ratio mode.

Specify the short exposure time by setting

the magnification ratio (×1 to ×64) with

regards to a long exposure time.

Notes

• When the wide dynamic range mode is ON, solarization may be

observed in the images of some subjects. This phenomenon is

unique to wide dynamic range mode, and is not an indication of a

camera malfunction.

• The frame rate during Wide Dynamic Range mode will be half of

that during standard mode.

Example: When Wide Dynamic Range mode is ON in 1080/30P

mode, the frame rate is 15 fps.

• Switching WD ON/OFF may cause three frames of invalid images

to be displayed.

Basic Functions

FCB-EH6300(GB) A-E23-100-15(1)

Threshold values

• You can set the threshold value that determines high

or low intensity.

• The minimum threshold value is 1h (decimal: 1), and

the maximum threshold value is FE1h (decimal:

4065).

• The default setting for the threshold value is 200h

(decimal: 512).

Grayscale image

(256 levels)

Color image

Binarization

process

Assign any

color

Temperature Reading Function

The conversion value (hex) of the temperature sensor

built into to the camera can be read by using a query

command. The conversion value has an error of ±3 C,

and because the temperature sensor is inside the

camera, this value is not the ambient temperature. Use

it as a reference value.

Slow shutter – Auto/Manual

When set to “Auto,” ensures that the slow shutter is set

automatically when the brightness drops. Effective only

when the AE mode is set to “Full Auto.”

Set to “Slow Shutter Manual” at shipment.

Note

The Slow Shutter Auto function is not available in WD mode.

Low-Illumination Chroma Suppress Mode

You can configure a chroma suppress mode for low-

illumination conditions. This can be useful when color

noise is particularly noticeable in such conditions.

Four levels (disabled and three levels) are available for

the low-illumination chroma suppress mode. Set the

effect to be applied at approximately 15 dB. Higher

setting values produce stronger chroma suppressing

effects.

ICR (IR Cut-Removable) Mode

An infrared (IR) Cut-Filter can be disengaged from the

image path for increased sensitivity in low light

environments. The ICR will automatically engage

depending on the ambient light, allowing the camera to

be effective in day/night environments.

When the auto ICR mode is set to ON, the image

becomes black and white.

Custom Color Gain

You can customize and configure the color gain. Use

this setting when bright color is particularly important.

The initial setting 100% (4h) can be set to range from

approx. 60% (Oh) to 200% (Eh) with 15 stages.

Custom Color Phase

You can customize and configure the color phase.

The initial setting 0 degrees (7h) is adjustable between

approx.

−14 degrees (0h) and +14 degrees (Eh), in

15 increments.

Auto ICR Mode

Auto ICR Mode automatically switches the settings

needed for attaching or removing the IR Cut Filter.

With a set level of darkness, the IR Cut Filter is

automatically disabled (ICR ON), and the infrared

sensitivity is increased. With a set level of brightness,

the IR Cut Filter is automatically enabled (ICR OFF).

Also, on systems equipped with an IR light, the internal

data of the camera is used to make the proper decisions

to avoid malfunctions.

Auto ICR Mode operates with the AE Full Auto setting.

ICR

SHUTTER

Dark Bright

AGC

MAX

IRIS

OPEN

Shutter 1/60 sec

ICR OFF U ON

GAIN

ICR ON

IRIS

When Auto Slow Shutter is ON

When Auto Slow Shutter is OFF (initial setting)

Note

When in Auto_ICR_OFF state and WB data is added (default), a

malfunction may occur when the subjects largely consisting of blue

and green colors are taken.

Basic Functions

FCB-EH6300(GB) A-E23-100-15(1)

Camera ID

The ID can be set up to 65,536 (0000 to FFFF). As this

will be memorized in the nonvolatile memory inside,

data will be saved regardless of whether it has been

backed up.

Effect

It consists of the following functions.

•

Neg. Art: Negative/Positive Reversal

•

Black White: Monochrome Image

Others

E-FLIP

This function turns the video output from the camera

upside down.

Mirror Image

This function reverses the video output from the

camera horizontally.

Freeze

This function captures an image in the field memory of

the camera so that this image can be output

continuously.

Because communication inside the camera is based on V cycle,

the captured image is always the one 3V to 4Vs after the

sending of a Command. Thus, you can not specify a time

period after sending EVEN, ODD or a Command.

Memory (Position preset)

Using the position preset function, 6 sets of camera

shooting conditions can be stored and recalled.

This function allows you to achieve the desired status

instantly, even without adjusting the following items

each time.

• Zoom Position

• Digital Zoom On/Off

• Focus Auto/Manual

• Focus Position

• AE Mode

• Shutter control parameters

• Bright Control

• Iris control parameters

• Gain control parameters

• Exposure Compensation On/Off

• Exposure Level

• Backlight Compensation On/Off

• Slow Shutter Auto/Manual

• White Balance Mode

• R/B Gain

• Aperture

• ICR Shoot On/Off

• WD On/Off

Custom Preset

As with the position preset function, the camera

shooting conditions can be stored and recalled. The

settings are recalled when the power is turned on.

For setting items, see the “Initial Settings, Custom Preset

and Backup” section on page 22.

User Memory Area

A user area of 16 bytes allows you to write data, such as

an ID for each customer, data for each system, and so

on, freely.

Note

Rewriting of memory is not unlimited. Be careful to avoid using the

memory area for such as unnecessary tasks as rewriting the

contents of the memory for every operation.

The camera’s default settings can be changed by the

8x 01 04 24 mm 0p 0q FF

mm: Register No. (=00 to 7F)

pq: Register Value (=00 to FF)

8x 09 04 24 mm FF

mm: Register No.

y0 50 0p 0p FF

pp: Register Value

(returned from the camera)

Example: To set communication speed to 38400 bps

8x 01 04 24 00 00 02 FF

After sending this command, turn power off and

back on (power reset) to resume communication

control at 38400 bps.

Example: Sending to confirm settings

8x 09 04 24 00 FF

y0 50 00 03 FF is returned from the camera

The register setting items and No. are as follows.

Baud Rate: 00

Communication speed can be changed.

Monitoring Mode: 72

This register “72” allows digital output mode

configuration.

For details on each output mode and parameter, see

“Register Setting” on page 50.

Output Enable: 73

“Analog Output”, “Digital Output”, or “Both” can be

set.

For details on parameters, see “Register Setting” on

page 50.

Zoom Limit: 50 (Wide end), 51 (Tele end)

The Wide and Tele zoom limits can be set.

E-Zoom Max: 52

The maximum digital zoom limit can be specified

(default is ×12).

剩余64页未读，继续阅读

open_cz

粉丝: 20
资源: 7

"Sony EH6300相机手册：功能、操作、注意事项详解！"

台达EH2系列PLC手册

通讯协议中 soi 7eh

PC817代替AQY211EH电路

typec eh作用

eh208串口工具能不能监控串口返回的信息

aqw212eh电路原理图

台达dvp eh3通讯读温度

ifconfig eh0

dp-eh400微型打印机

已知补码A1C.6EH 求其真值

利用两片四位运算器74181运算(6eH+03H )+(6eH||03H)。（||代表或运算）

EH4103是什么芯片

int 2eh和syscall选择哪个都行吗

MOV 3EH,#00H MOV P0,#0C0H CALL ENABLE MOV DPTR,#RIGHT CALL WRITE3 MOV 2EH,#2EH AJMP ERRJUDGE这段代码的作用是什么

如果霍尔传感器的的激励电流为4mA，灵敏度为3，磁感应强度为B=0.5T，那么霍尔电势EH为多少？最后的输出Uout是多少？

dword_815DC8 dd 0BB40E64Eh

mov [esp+8+var_4], 40004Eh的含义

台达dvp eh plc程序密码忘了怎么办

unity 控制SHARP XG-EH406UA 投影仪

d:\vc6.0\microsoft visual studio\vc98\include\eh.h(32) : fatal error C1189: #error : "eh.h is only for C++!"

最新资源