ETSI EN 300 328 V1.8.1：2.4GHz ISM频段宽带传输设备的电磁兼容与法规要求

需积分: 9 59 浏览量更新于2024-07-22 2 收藏 1.02MB PDF 举报

ETSI EN 300 328 V1.8.1（2012年6月版）是一项欧洲电信标准化组织(ETSI)发布的CE标准，全称为"电磁兼容性和无线电频谱问题(Electromagnetic Compatibility and Radio Spectrum Matters, ERM)：宽带传输系统规范"。该标准针对的是在2.4GHz工业、科学和医疗(ISM)频段内运行，并采用宽带调制技术的数据传输设备。它旨在确保这些设备在满足无线电频谱管理规定的同时，能够在无线局域网(LAN)和移动通信中提供可靠的服务。标准涵盖了欧盟无线电和电信设备(R&TDE)指令第3.2条基本要求的统一技术规范，特别关注数据传输的安全性、效率和互操作性。它涉及到的关键术语包括数据传输（Data）、ISM频段（Industrial, Scientific, and Medical）、局域网（LAN）、移动通信（Mobile）、无线电监管（Radio Regulation）、频谱共享(Spread Spectrum)以及射频设备(SRD)。此外，标准还规定了针对此类设备的测试和认证程序，确保它们符合严格的性能和辐射控制要求，从而避免对其他电子设备和公共安全造成干扰。 ETSI EN 300 328 V1.8.1适用于UHF频段的设备，例如无线路由器、蓝牙设备和智能家居设备等。用户在购买和使用这类产品时，应确保它们已通过该标准的认证，这通常意味着它们在设计和制造过程中已满足电磁兼容性和辐射限制的标准。需要注意的是，这份文档是经过ETSI注册的非营利协会编写的，且可供公众在线下载，其参考版本为PDF格式。在任何电子版本或印刷版本中，如果发现内容有差异，应当以PDF格式为准。对于任何关于标准的疑问或争议，应当参照印刷版作为最终的权威依据。 ETSI EN 300 328 V1.8.1对于电子产品制造商、无线设备开发者以及所有涉及ISM频段设备使用的人来说，都是至关重要的参考资料，它不仅指导着产品的设计与开发，也确保了全球市场的准入条件，对于维护一个有序和安全的无线电频谱环境至关重要。

ETSI

ETSI EN 300 328 V1.8.1 (2012

06)

OATS Open Air Test Site

OFDM Orthogonal Frequency Division Multiplexing

OOB Out Of Band

RBW Resolution BandWidth

RMS Root Mean Square

R&TTE Radio and Telecommunications Terminal Equipment

RF Radio Frequency

SAR Semi Anechoic Room

TL Threshold Level

Tx Transmitter

UUT Unit Under Test

VBW Video BandWidth

4 Technical specifications

4.1 Environmental profile

The technical requirements of the present document apply under the environmental profile for operation of the

equipment, which shall be stated by the supplier.

The equipment shall comply with all the technical requirements of the present document at all times when operating

within the boundary limits of the required operational environmental profile.

4.2 Equipment types

4.2.1 Modulation types

The present document defines two categories of Wide Band Data Transmission equipment:

• Equipment using Frequency Hopping Spread Spectrum (FHSS) modulation.

• Equipment using other types of wide band modulation (e.g. DSSS, OFDM, etc.).

All forms of wide band modulations, other than FHSS, are treated identically with regard to the requirements of the

present document.

The supplier shall declare which modulation type(s) applies to the equipment. See also clause 5.3.1.

4.2.2 Adaptive and non-adaptive equipment

The present document covers both adaptive and non-adaptive equipment.

Adaptive equipment uses an automatic mechanism which allows the equipment to adapt automatically to its

environment by identifying frequencies that are being used by other equipment.

Non-adaptive equipment does not use such an automatic mechanism and hence are subject to certain restrictions with

respect to using the medium (see clauses 4.3.1.5 and 4.3.2.4 for Medium Utilisation factor) in order to ensure sharing

with other equipment.

Adaptive equipment may have more than one adaptive mode implemented.

Adaptive equipment is allowed to operate in a non-adaptive mode.

The equipment shall comply with the corresponding requirements in each of the modes in which it can operate.

The supplier shall declare whether the equipment is adaptive equipment or non-adaptive equipment. In case of adaptive

equipment, the supplier shall declare if more than one adaptive mode is implemented and whether the equipment can

also operate in a non-adaptive mode. See also clause 5.3.1.

ETSI

ETSI EN 300 328 V1.8.1 (2012

06)

4.3 Technical requirements

4.3.1 Technical requirements for Frequency Hopping equipment

Equipment using FHSS modulation, and further referred to as Frequency Hopping equipment, shall comply with the

requirements in clauses 4.3.1.1 to 4.3.1.11.

For equipment using other forms of modulation, the requirements in clause 4.3.2 shall apply.

4.3.1.1 RF output power

This requirement applies to all types of Frequency Hopping equipment.

4.3.1.1.1 Definition

The RF output power is defined as the mean equivalent isotropically radiated power (e.i.r.p.) of the equipment during a

transmission burst.

4.3.1.1.2 Limit

The maximum RF output power for adaptive Frequency Hopping equipment shall be equal to or less than 20 dBm.

The maximum RF output power for non-adaptive Frequency Hopping equipment, shall be declared by the supplier. See

clause 5.3.1 m). The maximum RF output power for this equipment shall be equal to or less than the value declared by

the supplier. This declared value shall be equal to or less than 20 dBm.

This limit shall apply for any combination of power level and intended antenna assembly.

4.3.1.1.3 Conformance

The conformance tests for this requirement are (part of the procedure) defined in clause 5.3.2.

4.3.1.2 Duty Cycle, Tx-sequence, Tx-gap

These requirements apply to non-adaptive frequency hopping equipment or to adaptive frequency hopping equipment

operating in a non-adaptive mode.

These requirements do not apply for equipment with a maximum declared RF Output power of less than 10 dBm e.i.r.p.

or for equipment when operating in a mode where the RF Output power is less than 10 dBm e.i.r.p.

Medical devices requiring reverse compatibility with other medical devices placed on the market when earlier versions

of the present document were harmonised, are allowed to have an operating mode in which they do not have to comply

with the requirements for Duty Cycle, Tx-sequence and Tx-gap.

4.3.1.2.1 Definition

Duty Cycle is defined as the ratio of the total transmitter 'on'-time to an observation period. The observation period is

equal to the average dwell time multiplied by 100 or by 2 times the number of hopping frequencies (N) whichever is the

greater.

Tx-sequence is defined as a period in time during which a single or multiple transmissions may occur and which shall

be followed by a Tx-gap. These multiple transmissions within a single Tx-sequence may take place on the same

hopping frequency or on multiple hopping frequencies.

Tx-gap is defined as a period in time during which no transmissions occur.

NOTE: For non-adaptive frequency hopping equipment, the maximum Duty Cycle at which the equipment can

operate, is declared by the supplier. The equipment may have a dynamic behaviour with regard to duty

cycle and corresponding power level. See clause 5.3.1 e).

ETSI

ETSI EN 300 328 V1.8.1 (2012

06)

4.3.1.2.2 Limit

For non-adaptive FHSS equipment, the Duty Cycle shall be equal to or less than the maximum value declared by the

supplier. In addition, the maximum Tx-sequence time shall be 5 ms while the minimum Tx-gap time shall be 5 ms.

4.3.1.2.3 Conformance

The conformance tests for this requirement are (part of the procedure) defined in clause 5.3.2.

4.3.1.3 Dwell time, Minimum Frequency Occupation and Hopping Sequence

These requirements apply to all types of frequency hopping equipment.

4.3.1.3.1 Definition

The Dwell Time is the time that a particular hopping frequency would be occupied by the transmitter during a single

hop. The equipment itself is not required to transmit on this hopping frequency during the Dwell Time.

The Minimum Frequency Occupation Time is the minimum time each hopping frequency shall be occupied within a

given period.

The Hopping Sequence of a Frequency Hopping system is the unrepeated pattern of the hopping frequencies used by

the equipment.

4.3.1.3.2 Limit

4.3.1.3.2.1 Non-adaptive frequency hopping systems

The accumulated Dwell Time on any hopping frequency shall not be greater than 15 ms within any period of 15 ms

multiplied by the minimum number of hopping frequencies (N) that have to be used. Non-adaptive medical devices

requiring reverse compatibility with other medical devices placed on the market when earlier versions of the present

document were harmonised, are allowed to have an operating mode in which the maximum dwell time is 400 ms.

The hopping sequence(s) shall contain at least N hopping frequencies where N is 15 or 15 divided by the minimum

Hopping Frequency Separation in MHz, whichever is the greater.

The Minimum Frequency Occupation Time shall be equal to one dwell time within a period not exceeding four times

the product of the dwell time per hop and the number of hopping frequencies in use.

4.3.1.3.2.2 Adaptive frequency hopping systems

Adaptive Frequency Hopping systems shall be capable of operating over a minimum of 70 % of the band specified in

clause 1.

The maximum accumulated dwell time on any hopping frequency shall be 400 ms within any period of 400 ms

multiplied by the minimum number of hopping frequencies (N) that have to be used.

The hopping sequence(s) shall contain at least N hopping frequencies at all times, where N is 15 or 15 divided by the

minimum Hopping Frequency Separation in MHz, whichever is the greater.

The Minimum Frequency Occupation Time shall be equal to one dwell time within a period not exceeding four times

the product of the dwell time per hop and the number of hopping frequencies in use.

4.3.1.3.3 Other Requirements

Frequency Hopping equipment shall transmit on a minimum of two hopping frequencies.

For non-Adaptive Frequency Hopping equipment, when not transmitting on a hopping frequency, the equipment has to

occupy that frequency for the duration of the typical dwell time.

For Adaptive Frequency Hopping systems using LBT based DAA, if a signal is detected during the CCA, these systems

may jump immediately to the next frequency in the hopping sequence (see clause 4.3.1.6.1.2 point 2) provided the limit

for maximum dwell is respected.

ETSI

ETSI EN 300 328 V1.8.1 (2012

06)

4.3.1.3.4 Conformance

The conformance tests for this requirement are defined in clause 5.3.4.

4.3.1.4 Hopping Frequency Separation

This requirement applies to all types of frequency hopping equipment.

4.3.1.4.1 Definition

The Hopping Frequency Separation is the frequency separation between 2 adjacent hopping frequencies.

4.3.1.4.2 Limit

4.3.1.4.2.1 Non-adaptive frequency hopping systems

The minimum Hopping Frequency Separation shall be equal to Occupied Channel Bandwidth (see clause 4.3.1.7) of a

single hop, with a minimum separation of 100 kHz.

4.3.1.4.2.2 Adaptive frequency hopping systems

The minimum Hopping Frequency Separation shall be 100 kHz.

4.3.1.4.3 Conformance

The conformance tests for this requirement are defined in clause 5.3.5.

4.3.1.5 Medium Utilisation (MU) factor

This requirement does not apply to adaptive equipment unless operating in a non-adaptive mode.

In addition, this requirement does not apply for equipment with a maximum declared RF Output power level of less

than 10 dBm e.i.r.p. or for equipment when operating in a mode where the RF Output power is less than 10 dBm e.i.r.p.

Medical devices requiring reverse compatibility with other medical devices placed on the market when earlier versions

of the present document were harmonised, are allowed to have an operating mode in which they have a Medium

Utilisation above the limit defined in clause 4.3.1.5.2.

4.3.1.5.1 Definition

The Medium Utilisation (MU) factor is a measure to quantify the amount of resources (Power and Time) used by

non-adaptive equipment. The Medium Utilisation factor is defined by the formula:

MU = (P/100 mW) × DC

where: MU is Medium Utilisation factor in %.

P is the RF output power as defined in clause 4.3.1.1.1 expressed in mW.

DC is the Duty Cycle as defined in clause 4.3.1.2.1 expressed in %.

NOTE: The equipment may have dynamic behaviour with regard to duty cycle and corresponding power level.

See clause 5.3.1 e).

4.3.1.5.2 Limit

The maximum Medium Utilisation factor for non-adaptive Frequency Hopping equipment shall be 10 %.

4.3.1.5.3 Conformance

The conformance tests for this requirement are (part of the procedure) defined in clause 5.3.2.

剩余83页未读，继续阅读

名成在天下

粉丝: 3
资源: 9

ETSI EN 300 328 V1.8.1：2.4GHz ISM频段宽带传输设备的电磁兼容与法规要求

ETSI en_300328v1.8.1

ETSI EN 300 328 V2.2.2.pdf

ETSI EN 300 468 V1.8.1

ETSI EN 300 468 v1.8.1 (2007-10 Final draft)

ETSI EN 300 468 V1.8.1: DVB数字电视服务信息规范

ETSI EN 300468 V1.8.1：DVB数字电视EPG开发关键文档

epg开发文档En300468.V1.8.1

EN300328 V 1.8.1 测试标准

EN301489-1V1.8.1

ETSI 300328v1.8.1：2.4GHz ISM频段宽频传输设备的电磁兼容标准

最新资源