没有合适的资源?快使用搜索试试~ 我知道了~
首页科勒5.0发电机安全操作与维护指南
科勒5.0发电机安全操作与维护指南
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 119 浏览量
更新于2024-06-13
收藏 7.08MB PDF 举报
科勒5.0发电机使用手册是一份详尽的指导文档,旨在确保用户在操作科勒公司生产的5.0系列发电机时的安全与有效性。该手册强调了在使用前必须仔细阅读所有安全注意事项和操作指南,这包括但不限于: 1. 安全预防:在启动设备之前,务必确保引擎已完全停止并且设备水平放置,以防在维护或服务过程中发生意外。操作人员应避免在运转中加油,因为汽油是易燃的,其蒸气一旦遇到明火或火花,可能导致火灾和严重烧伤。 2. 储存与存放:汽油应储存在经过批准的容器内,并存放在通风良好的无人区域,远离火花和火焰。避免在吸烟或有明火附近加油,防止燃料溢出并引发火灾。汽油不应作为清洁剂使用。 3. 旋转部件风险:发电机的旋转部件具有高度危险性,可能会导致严重的人身伤害。在发电机运行期间,操作者及其周围的人和物应保持适当距离,防止触及移动部件造成切割、撞伤等事故。 4. 产品信息记录:手册建议记录产品的序列号、购买日期等信息,以便在需要更换零件或寻求保修服务时提供参考。这些信息对于确认设备身份、确保维修质量和保持保修权益至关重要。 5. 规格说明:手册中提供了具体型号TP-7033-CMP8/18a的相关参数,如序列号和可能的附件信息,这有助于用户了解他们的特定设备性能和适用范围。 6. 官方资源:手册引用KohlerPower.com,提示用户在遇到问题或需要更多信息时访问科勒官方网站,获取最新的技术支持和服务信息。 科勒5.0发电机使用手册是一部重要的参考资料,它详细指导用户如何正确、安全地操作和维护这款发电机,旨在保障用户在享受电力供应的同时,避免潜在的风险。在实际操作中,用户应严格遵循手册中的指示,以确保个人安全和设备正常运行。
资源详情
资源推荐
8 TP-7033-CMP 8/18a KohlerPower.com
5. Check sediment bowl cover and gasket.
Replace them if they are damaged.
6. Reinstall sediment bowl.
7. Open tank fuel valve (R).
8. Wipe off any trace of fuel with a clean cloth
and check for any leakage.
Spark Plugs
CAUTION
Electrical Shock can cause injury.
Do not touch wires while
generator is running.
Never operate generator in rain or snow.
Never touch generator with wet hands or
electrical shock may occur.
Clean out spark plug recess. Remove spark
plug (K) and replace.
1. Check gap using wire feeler gauge. Adjust
gap, see specication table for adjustment.
2. Install spark plug (K) into cylinder head.
3. Torque spark plug (K) to 20 ft. lb. (27 N·m).
Air Cleaner
NOTE: Operating engine with loose or
damaged air cleaner components
could cause premature wear and
failure. Replace all bent or damaged
components.
1. Remove screw (N) and air cleaner cover (O).
2. Remove foam element (P) from air cleaner
base (Q).
3. Wash foam element (P) in warm water with
detergent. Rinse and allow to air dry.
4. Lightly oil foam element (P) with new engine
oil; squeeze out excess oil.
5. Reinstall foam element (P) into air cleaner
base (Q).
6. Reinstall air cleaner cover (O) and secure
with screw (N).
Breather Tube
Ensure both ends of breather tube are properly
connected.
Fuel Level
WARNING
Explosive Fuel can cause res
and severe burns.
Do not ll fuel tank while
generator is hot or running.
Gasoline is extremely ammable and
its vapors can explode if ignited. Store
gasoline only in approved containers, in
well ventilated, unoccupied buildings, away
from sparks or ames. Spilled fuel could
ignite if it comes in contact with hot parts or
sparks from ignition. Never use gasoline as a
cleaning agent.
Visually check level of fuel. If necessary, ll up.
1. Unscrew fuel tank cap (F).
2. Fill tank until fuel gauge shows F, using
funnel and taking care not to spill any fuel.
3. Screw down fuel tank cap (F) tightly.
Fuel Line
Low permeation fuel line must be installed on
carbureted Kohler Co. engines to maintain EPA
and CARB regulatory compliance.
Fuel Filter
1. Open fuel tank cap (F).
2. Remove fuel lter (S) from tank neck.
3. Clean fuel lter (S) with a non-ammable
solvent or solvent with a high ash point. Dry
it fully. Replace as necessary.
4. Reinstall fuel lter (S).
5. Reinstall fuel tank cap (F).
Sediment Bowl
1. Close fuel valve (R) and remove cover
screws and nuts.
2. Remove cover.
3. Remove sediment bowl.
4. Clean sediment bowl with a non-ammable
solvent or solvent with a high ash point. Dry
it fully.
9
TP-7033-CMP 8/18a
KohlerPower.com
EN
AC Rated Power
AC rated power is maximum amount of power
generator can support.
AC Surge Power
AC surge power is additional power generator
momentarily produces to aid in starting of
electrical devices requiring power above
generator's rated power requirements.
Overload (Capacity of Generator)
Never exceed rated load of generator (in Amps
and/or Watts) when it is running continuously.
See specications table for rated outputs.
Before connecting and operating generator,
calculate electrical power required by electric
appliances (in Watts). This electrical power
rating is usually found on manufacturer's
plate on bulbs, electrical appliances, motors,
etc. Sum total of power required by these
appliances should not exceed nominal power
rating of generator.
Circuit protectors (C) will stop power to
protected receptacles (B & D) when an
overload of a connected electrical device is
detected or AC output voltage rises to protect
generator and any connected electric devices.
When overload occurs and power generation
stops, proceed as follows:
1. Turn off any connected electric devices and
stop generator.
2. Reduce total wattage of connected electric
devices within application range.
3. Check for blockages in cooling air inlet and
outlet areas and around control unit. If any
blockages are found, remove them.
4. After checking, restart generator.
Air Cooling
WARNING
Hot Parts can cause severe
burns.
Do not touch generator while
operating or just after stopping.
Never operate generator with heat shields or
guards removed. Do not modify generator.
Place generator in a place where pedestrians
or children are not likely to touch generator.
Be sure to carry generator only by its
carrying handles.
Proper cooling is essential. To prevent over
heating, ensure air cooling inlet and outlet
areas are clean and unobstructed. Avoid
spraying water at wiring harness or any
electrical components. Refer to Maintenance
Schedule.
Ground Terminal
Ground terminal (E) connects earth line for
prevention of electric shock. When electric
device is grounded, be sure to ground
generator also.
Connect generator to ground: Attach a 6 AWG
(10 mm
2
) copper wire to generator’s ground
connection and to a galvanized steel grounding
rod (not provided) driven 3.3 ft. (1 m) into
ground.
Connecting Alternating Current (AC)
NOTE: Ensure all electric devices including
lines and plug connection are in good
condition before connection to
generator.
NOTE: Ensure total load is within generator
rated output.
NOTE: Ensure receptacle load current is within
receptacle rated current.
1. Start engine.
2. Plug into AC receptacle (B or D).
3. Turn on any electric devices.
剩余43页未读,继续阅读
wwwarewow
- 粉丝: 4590
- 资源: 2471
下载权益
电子书特权
VIP文章
课程特权
开通VIP
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
最新资源
- 构建Cadence PSpice仿真模型库教程
- VMware 10.0安装指南:步骤详解与网络、文件共享解决方案
- 中国互联网20周年必读:影响行业的100本经典书籍
- SQL Server 2000 Analysis Services的经典MDX查询示例
- VC6.0 MFC操作Excel教程:亲测Win7下的应用与保存技巧
- 使用Python NetworkX处理网络图
- 科技驱动:计算机控制技术的革新与应用
- MF-1型机器人硬件与robobasic编程详解
- ADC性能指标解析:超越位数、SNR和谐波
- 通用示波器改造为逻辑分析仪:0-1字符显示与电路设计
- C++实现TCP控制台客户端
- SOA架构下ESB在卷烟厂的信息整合与决策支持
- 三维人脸识别:技术进展与应用解析
- 单张人脸图像的眼镜边框自动去除方法
- C语言绘制图形:余弦曲线与正弦函数示例
- Matlab 文件操作入门:fopen、fclose、fprintf、fscanf 等函数使用详解
资源上传下载、课程学习等过程中有任何疑问或建议,欢迎提出宝贵意见哦~我们会及时处理!
点击此处反馈
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功