STM32的PA9和PA10是什么串口
时间: 2024-04-12 08:05:24 浏览: 32
在STM32中,PA9和PA10可以用作USART1的TX和RX引脚,因此它们可以用作USART1串口的数据传输引脚。
USART1是一种通用异步收发传输器,可以实现串口通信。在使用USART1时,需要进行正确的初始化和配置,包括波特率、数据位、停止位、校验位等参数的设置。然后可以使用USART1的发送和接收函数来实现数据的发送和接收。
需要注意的是,PA9和PA10也可以用作其他外设的引脚,例如定时器通道输入捕获、PWM输出等,使用时需要进行正确的配置。因此,在使用PA9和PA10时,需要查看相关资料并进行正确的配置,以满足具体应用的需求。
相关问题
STM32f103C8T6PA9和PA10引脚是收发引脚吗
是的,STM32F103C8T6微控制器的PA9和PA10引脚是USART1串口通信的收发引脚。在STM32中,USART通信是通过UART和USART外设实现的。USART是通用同步异步收发传输器,支持全双工和半双工通信模式。PA9和PA10引脚是USART1的TX和RX引脚,用于与其他设备进行串口通信。
STM32F4串口1PA9、PA10接MAX3490,RS422的程序
以下是基于STM32F4的串口1(PA9、PA10)接MAX3490,实现RS422通信的示例程序:
```c
#include "stm32f4xx.h"
#include "stm32f4xx_conf.h"
UART_HandleTypeDef UART_HandleStruct;
void InitializeUART(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// Enable GPIOA clock
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
// Enable USART1 clock
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
// Configure USART1 Tx (PA9) as alternate function push-pull
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Configure USART1 Rx (PA10) as input floating
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Connect USART1 pins to AF7
GPIO_PinAFConfig(GPIOA, GPIO_PinSource9, GPIO_AF_USART1);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource10, GPIO_AF_USART1);
// Configure USART1
UART_HandleStruct.Instance = USART1;
UART_HandleStruct.Init.BaudRate = 115200;
UART_HandleStruct.Init.WordLength = UART_WORDLENGTH_8B;
UART_HandleStruct.Init.StopBits = UART_STOPBITS_1;
UART_HandleStruct.Init.Parity = UART_PARITY_NONE;
UART_HandleStruct.Init.HwFlowCtl = UART_HWCONTROL_NONE;
UART_HandleStruct.Init.Mode = UART_MODE_TX_RX;
HAL_UART_Init(&UART_HandleStruct);
}
void InitializeMAX3490(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// Enable GPIOB clock
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
// Configure MAX3490 /RE (PB12) as output push-pull
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOB, &GPIO_InitStructure);
// Configure MAX3490 /DE (PB13) as output push-pull
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOB, &GPIO_InitStructure);
// Enable MAX3490 transmit mode
GPIO_ResetBits(GPIOB, GPIO_Pin_12);
GPIO_SetBits(GPIOB, GPIO_Pin_13);
}
int main(void)
{
uint8_t txData[] = "Hello, world!\r\n";
uint8_t rxData[32];
// Initialize UART and MAX3490
InitializeUART();
InitializeMAX3490();
while(1)
{
// Send data
HAL_UART_Transmit(&UART_HandleStruct, txData, sizeof(txData), HAL_MAX_DELAY);
// Switch to receive mode
GPIO_SetBits(GPIOB, GPIO_Pin_12);
GPIO_ResetBits(GPIOB, GPIO_Pin_13);
// Receive data
HAL_UART_Receive(&UART_HandleStruct, rxData, sizeof(rxData), HAL_MAX_DELAY);
// Switch back to transmit mode
GPIO_ResetBits(GPIOB, GPIO_Pin_12);
GPIO_SetBits(GPIOB, GPIO_Pin_13);
}
}
```
在此示例程序中,我们首先初始化了UART和MAX3490的GPIO口。在主循环中,我们先使用UART发送了一个字符串,然后将MAX3490切换到接收模式,等待接收数据。当接收完成后,再将MAX3490切换回发送模式,继续发送数据。
需要注意的是,MAX3490的DE和RE引脚需要通过GPIO控制,用于切换发送和接收模式。在发送模式下,RE为高电平,DE为低电平;在接收模式下,RE为低电平,DE为高电平。在代码中,我们通过GPIO_SetBits和GPIO_ResetBits函数实现了引脚的电平控制。