帮我将代码修改为标准库 void atim_timx_cplm_pwm_init(uint16_t arr, uint16_t psc) { TIM_OC_InitTypeDef sConfigOC ; g_atimx_cplm_pwm_handle.Instance = ATIM_TIMX_CPLM; /* 定时器x / g_atimx_cplm_pwm_handle.Init.Prescaler = psc; / 定时器预分频系数 / g_atimx_cplm_pwm_handle.Init.CounterMode = TIM_COUNTERMODE_UP; / 向上计数模式 / g_atimx_cplm_pwm_handle.Init.Period = arr; / 自动重装载值 / g_atimx_cplm_pwm_handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; / 时钟分频因子 / g_atimx_cplm_pwm_handle.Init.RepetitionCounter = 0; / 重复计数器寄存器为0 / g_atimx_cplm_pwm_handle.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_ENABLE; / 使能影子寄存器TIMx_ARR / HAL_TIM_PWM_Init(&g_atimx_cplm_pwm_handle) ; / 设置PWM输出 / sConfigOC.OCMode = TIM_OCMODE_PWM1; / PWM模式1 / sConfigOC.Pulse = 0; / 比较值为0 / sConfigOC.OCPolarity = TIM_OCPOLARITY_LOW; / OCy 低电平有效 / sConfigOC.OCNPolarity = TIM_OCNPOLARITY_LOW; / OCyN 低电平有效 / sConfigOC.OCFastMode = TIM_OCFAST_ENABLE; / 不使用快速模式 / sConfigOC.OCIdleState = TIM_OCIDLESTATE_RESET; / 主通道的空闲状态 / sConfigOC.OCNIdleState = TIM_OCNIDLESTATE_RESET; / 互补通道的空闲状态 / HAL_TIM_PWM_ConfigChannel(&g_atimx_cplm_pwm_handle, &sConfigOC, ATIM_TIMX_CPLM_CHY); / 配置后默认清CCER的互补输出位 / / 设置死区参数，开启死区中断 / sBreakDeadTimeConfig.OffStateRunMode = TIM_OSSR_ENABLE; / OSSR设置为1 / sBreakDeadTimeConfig.OffStateIDLEMode = TIM_OSSI_DISABLE; / OSSI设置为0 / sBreakDeadTimeConfig.LockLevel = TIM_LOCKLEVEL_OFF; / 上电只能写一次，需要更新死区时间时只能用此值 / sBreakDeadTimeConfig.DeadTime = 0X0F; / 死区时间 / sBreakDeadTimeConfig.BreakState = TIM_BREAK_DISABLE; / BKE = 0, 关闭BKIN检测 / sBreakDeadTimeConfig.BreakPolarity = TIM_BREAKPOLARITY_LOW; / BKP = 1, BKIN低电平有效 / sBreakDeadTimeConfig.AutomaticOutput = TIM_AUTOMATICOUTPUT_DISABLE; / 使能AOE位，允许刹车后自动恢复输出 / HAL_TIMEx_ConfigBreakDeadTime(&g_atimx_cplm_pwm_handle, &sBreakDeadTimeConfig); / 设置BDTR寄存器 */ }

以下是修改后的标准库代码：

void atim_timx_cplm_pwm_init(uint16_t arr, uint16_t psc)
{
    TIM_HandleTypeDef g_atimx_cplm_pwm_handle;
    TIM_OC_InitTypeDef sConfigOC;
    TIM_BreakDeadTimeConfigTypeDef sBreakDeadTimeConfig;

    g_atimx_cplm_pwm_handle.Instance = ATIM_TIMX_CPLM;
    g_atimx_cplm_pwm_handle.Init.Prescaler = psc;
    g_atimx_cplm_pwm_handle.Init.CounterMode = TIM_COUNTERMODE_UP;
    g_atimx_cplm_pwm_handle.Init.Period = arr;
    g_atimx_cplm_pwm_handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
    g_atimx_cplm_pwm_handle.Init.RepetitionCounter = 0;
    g_atimx_cplm_pwm_handle.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_ENABLE;

    HAL_TIM_PWM_Init(&g_atimx_cplm_pwm_handle);

    sConfigOC.OCMode = TIM_OCMODE_PWM1;
    sConfigOC.Pulse = 0;
    sConfigOC.OCPolarity = TIM_OCPOLARITY_LOW;
    sConfigOC.OCNPolarity = TIM_OCNPOLARITY_LOW;
    sConfigOC.OCFastMode = TIM_OCFAST_ENABLE;
    sConfigOC.OCIdleState = TIM_OCIDLESTATE_RESET;
    sConfigOC.OCNIdleState = TIM_OCNIDLESTATE_RESET;

    HAL_TIM_PWM_ConfigChannel(&g_atimx_cplm_pwm_handle, &sConfigOC, ATIM_TIMX_CPLM_CHY);

    sBreakDeadTimeConfig.OffStateRunMode = TIM_OSSR_ENABLE;
    sBreakDeadTimeConfig.OffStateIDLEMode = TIM_OSSI_DISABLE;
    sBreakDeadTimeConfig.LockLevel = TIM_LOCKLEVEL_OFF;
    sBreakDeadTimeConfig.DeadTime = 0X0F;
    sBreakDeadTimeConfig.BreakState = TIM_BREAK_DISABLE;
    sBreakDeadTimeConfig.BreakPolarity = TIM_BREAKPOLARITY_LOW;
    sBreakDeadTimeConfig.AutomaticOutput = TIM_AUTOMATICOUTPUT_DISABLE;

    HAL_TIMEx_ConfigBreakDeadTime(&g_atimx_cplm_pwm_handle, &sBreakDeadTimeConfig);
}

注意：以上代码是基于您提供的代码进行修改的，没有进行实际测试，可能需要根据实际情况进行调整。