使用串口方式发送一个字节的代码
时间: 2024-04-08 11:34:40 浏览: 17
使用串口方式发送一个字节的代码可以根据具体平台和串口库实现。以下是示例使用Arduino平台的Serial库发送一个字节的代码:
```c++
#include <Arduino.h>
void SendByte(uint8_t byte) {
Serial.write(byte); // 使用Serial库的write函数发送字节
}
void setup() {
Serial.begin(9600); // 初始化串口通信,设置波特率为9600
}
void loop() {
// 示例发送一个字节,可以根据需要修改发送的字节值
uint8_t data = 0xAB;
SendByte(data);
delay(1000); // 延时1秒
}
```
在这个示例中,使用了Arduino平台的Serial库来实现串口通信。在setup函数中,通过Serial.begin函数初始化串口通信,并设置波特率为9600。在loop函数中,示例发送一个字节0xAB,可以根据需要修改发送的字节值。使用SendByte函数来发送字节,其中使用Serial.write函数将字节发送出去。
请根据你的具体平台和串口库进行相应的调整,以实现串口方式发送一个字节的操作。
相关问题
stm32hal库向串口一发送一个字节例程
以下是使用STM32 HAL库向串口发送一个字节的基本例程:
```c
#include "stm32f4xx_hal.h"
/* 定义串口句柄 */
UART_HandleTypeDef huart2;
int main(void)
{
/* 初始化HAL库 */
HAL_Init();
/* 配置串口 */
huart2.Instance = USART2;
huart2.Init.BaudRate = 115200;
huart2.Init.WordLength = UART_WORDLENGTH_8B;
huart2.Init.StopBits = UART_STOPBITS_1;
huart2.Init.Parity = UART_PARITY_NONE;
huart2.Init.Mode = UART_MODE_TX_RX;
huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
huart2.Init.OverSampling = UART_OVERSAMPLING_16;
HAL_UART_Init(&huart2);
while (1)
{
/* 发送一个字节 */
uint8_t data = 0x55;
HAL_UART_Transmit(&huart2, &data, 1, HAL_MAX_DELAY);
/* 延时 */
HAL_Delay(1000);
}
}
```
在上面的代码中,我们首先初始化了HAL库,然后配置了串口的一些参数(如波特率、数据位数、停止位数、校验位等)。在while循环中,我们使用了`HAL_UART_Transmit`函数发送了一个字节,其第一个参数是串口句柄,第二个参数是发送的数据指针,第三个参数是数据长度,第四个参数是最大延迟时间。
注意:在使用HAL库时,需要先调用各个外设的初始化函数(如`HAL_UART_Init`)来配置外设,否则会出现各种问题。
如何基于AT32F421写一个串口接收发送8个字节数据的代码
下面是一个基于AT32F421的串口接收发送8个字节数据的代码示例:
```c
#include <stdio.h>
#include "at32f4xx.h"
#define UART_TX_PIN GPIO_Pin_9
#define UART_RX_PIN GPIO_Pin_10
#define UART_GPIO_PORT GPIOA
#define UART_GPIO_CLK RCC_APB2Periph_GPIOA
#define UART_CLK RCC_APB1Periph_USART2
#define UART USART2
void init_uart()
{
USART_InitTypeDef USART_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
// Enable GPIO clock
RCC_APB2PeriphClockCmd(UART_GPIO_CLK, ENABLE);
// Enable UART clock
RCC_APB1PeriphClockCmd(UART_CLK, ENABLE);
// Configure UART pins
GPIO_InitStructure.GPIO_Pin = UART_TX_PIN | UART_RX_PIN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(UART_GPIO_PORT, &GPIO_InitStructure);
// Configure UART
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(UART, &USART_InitStructure);
// Enable UART
USART_Cmd(UART, ENABLE);
}
void uart_send(uint8_t *buf, uint8_t len)
{
uint8_t i;
for (i = 0; i < len; i++) {
USART_SendData(UART, buf[i]);
while (USART_GetFlagStatus(UART, USART_FLAG_TXE) == RESET);
}
}
void uart_receive(uint8_t *buf, uint8_t len)
{
uint8_t i;
for (i = 0; i < len; i++) {
while (USART_GetFlagStatus(UART, USART_FLAG_RXNE) == RESET);
buf[i] = USART_ReceiveData(UART);
}
}
int main(void)
{
uint8_t tx_buf[8] = {0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08};
uint8_t rx_buf[8];
// Initialize UART
init_uart();
// Send data
uart_send(tx_buf, 8);
// Receive data
uart_receive(rx_buf, 8);
// Do something with received data
while (1);
}
```
在这个示例中,我们使用USART2作为串口,并使用PA9和PA10作为UART的TX和RX引脚。我们首先需要初始化UART,然后可以使用uart_send()函数发送8个字节的数据,并使用uart_receive()函数接收8个字节的数据。在上面的示例中,我们只是打印收到的数据。