上面的一段代码中 i < address+16 是什么意思
时间: 2024-04-09 16:32:22 浏览: 27
在上述代码中,`i < address+16` 是一个循环条件,表示在执行擦除操作时要循环擦除从 `address` 开始的连续16个地址的数据。
当执行擦除操作时,Flash存储器通常需要按块或扇区擦除。在这个示例中,假设Flash存储器的地址是按字节寻址的,每个地址对应一个字节。所以 `i < address+16` 表示从 `address` 开始,循环擦除连续的16个地址的数据。
这样的循环条件可以确保在执行擦除操作时,正确地擦除指定地址及其后续的15个地址的数据。具体的擦除操作可能需要参考Flash存储器的规格说明或数据手册来确定正确的擦除方式和地址范围。
相关问题
for(i = 0; i < 48; i++) { VectorTable[i] = *(__IO uint32_t*)(Application1Address + (i<<2)); }
这段代码是一个循环,用于将地址为`Application1Address`的内存中的数据复制到`VectorTable`数组中。循环从0到47遍历,每次迭代将`Application1Address + (i<<2)`处的数据转换为`__IO uint32_t`类型,并赋值给`VectorTable[i]`。
其中,`(i<<2)`表示将i左移2位,相当于将i乘以4。这是因为`__IO uint32_t`类型占用4个字节,每次迭代都需要移动4个字节。
需要注意的是,这段代码假设`Application1Address`是一个有效的内存地址,并且在该地址开始的连续48个字节中包含了有效的数据。确保在使用该代码之前,已经分配了足够的内存空间,并且`Application1Address`指向了正确的数据位置。
此外,由于涉及到直接访问内存和类型转换,建议在使用这段代码时谨慎操作,并确保了解所操作的内存和数据类型的具体要求和约束。
编写一段I2C驱动代码
以下是一个简单的I2C驱动代码示例,仅供参考:
```
#include <stdint.h>
#include <stdbool.h>
#include "inc/hw_memmap.h"
#include "inc/hw_types.h"
#include "driverlib/gpio.h"
#include "driverlib/pin_map.h"
#include "driverlib/i2c.h"
#include "driverlib/sysctl.h"
#define I2C_SLAVE_ADDRESS 0x50
void I2C_Init(void)
{
// Enable I2C0
SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C0);
// Enable GPIOB
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
// Configure PB2 as SDA and PB3 as SCL
GPIOPinConfigure(GPIO_PB2_I2C0SDA);
GPIOPinConfigure(GPIO_PB3_I2C0SCL);
GPIOPinTypeI2CSCL(GPIO_PORTB_BASE, GPIO_PIN_3);
GPIOPinTypeI2C(GPIO_PORTB_BASE, GPIO_PIN_2);
// Configure I2C0
I2CMasterInitExpClk(I2C0_BASE, SysCtlClockGet(), false);
// Set slave address
I2CMasterSlaveAddrSet(I2C0_BASE, I2C_SLAVE_ADDRESS, false);
}
void I2C_Write(uint8_t *data, uint8_t numBytes)
{
uint8_t i;
// Send start condition
I2CMasterControl(I2C0_BASE, I2C_MASTER_CMD_SINGLE_SEND);
while(I2CMasterBusy(I2C0_BASE));
// Send data
for (i = 0; i < numBytes; i++)
{
I2CMasterDataPut(I2C0_BASE, data[i]);
I2CMasterControl(I2C0_BASE, I2C_MASTER_CMD_BURST_SEND_CONT);
while(I2CMasterBusy(I2C0_BASE));
}
// Send stop condition
I2CMasterControl(I2C0_BASE, I2C_MASTER_CMD_BURST_SEND_FINISH);
while(I2CMasterBusy(I2C0_BASE));
}
void I2C_Read(uint8_t *data, uint8_t numBytes)
{
uint8_t i;
// Send start condition
I2CMasterControl(I2C0_BASE, I2C_MASTER_CMD_SINGLE_SEND);
while(I2CMasterBusy(I2C0_BASE));
// Send slave address with read bit set
I2CMasterSlaveAddrSet(I2C0_BASE, I2C_SLAVE_ADDRESS, true);
I2CMasterControl(I2C0_BASE, I2C_MASTER_CMD_BURST_RECEIVE_START);
while(I2CMasterBusy(I2C0_BASE));
// Receive data
for (i = 0; i < numBytes - 1; i++)
{
I2CMasterControl(I2C0_BASE, I2C_MASTER_CMD_BURST_RECEIVE_CONT);
while(I2CMasterBusy(I2C0_BASE));
data[i] = I2CMasterDataGet(I2C0_BASE);
}
// Receive last byte of data
I2CMasterControl(I2C0_BASE, I2C_MASTER_CMD_BURST_RECEIVE_FINISH);
while(I2CMasterBusy(I2C0_BASE));
data[numBytes-1] = I2CMasterDataGet(I2C0_BASE);
}
```
这个代码片段演示了如何使用TI Tiva C系列微控制器的I2C模块。它包括初始化I2C模块、写入数据和读取数据的函数。请注意,此代码片段仅适用于特定的硬件平台和运行时库版本。如果你要在其他平台上使用I2C驱动程序,请根据需要进行修改。