dma串口重写printf
时间: 2023-07-23 10:57:49 浏览: 58
如果你想在DMA串口上重写printf函数,你需要做以下几个步骤:
1. 首先,你需要了解DMA串口的工作原理和相关寄存器的配置。DMA(直接内存访问)可以在不使用CPU的情况下完成数据的传输,因此在重写printf函数时,你可以使用DMA来发送数据。
2. 然后,你需要编写一个新的printf函数来替代标准库中的printf函数。这个新的函数将会使用DMA来发送数据到串口。
3. 在新的printf函数中,你需要配置DMA控制器以将要发送的数据从内存复制到串口的数据寄存器中。具体配置方式取决于你使用的芯片型号和开发环境。
4. 在新的printf函数中,你还需要处理格式化字符串和变量参数,将它们转换为实际要发送的数据。
请注意,上述步骤是一个概述,并且具体的实现方式可能因芯片型号、开发环境和需求而有所不同。因此,在实际操作中,请参考相关的芯片手册、开发环境文档和示例代码来进行具体的实现。
相关问题
stm32cubemx dma串口通信printf
可以使用STM32CubeMX配置DMA来实现串口通信中的printf功能。下面是一个示例代码,可以将printf输出通过DMA发送到串口:
1. 首先,确保你已经在STM32CubeMX中启用了相关的USART和DMA功能,并正确配置了串口通信的参数。
2. 在生成的代码中找到USART相关的初始化函数,一般位于`usart.c`文件中。在该函数中,找到`HAL_UART_MspInit()`函数的实现。
3. 在`HAL_UART_MspInit()`函数的开头添加以下代码,用于初始化DMA传输相关的资源:
```c
/* DMA interrupt init */
/* DMA1_Channel4_IRQn interrupt configuration */
HAL_NVIC_SetPriority(DMA1_Channel4_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(DMA1_Channel4_IRQn);
```
4. 接下来,在`HAL_UART_MspInit()`函数中添加以下代码,用于配置DMA传输:
```c
/* Enable the DMA transfer for transmit */
__HAL_RCC_DMA1_CLK_ENABLE();
hdma_usart2_tx.Instance = DMA1_Channel4;
hdma_usart2_tx.Init.Direction = DMA_MEMORY_TO_PERIPH;
hdma_usart2_tx.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_usart2_tx.Init.MemInc = DMA_MINC_ENABLE;
hdma_usart2_tx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;hdma_usart2_tx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
hdma_usart2_tx.Init.Mode = DMA_NORMAL;
hdma_usart2_tx.Init.Priority = DMA_PRIORITY_LOW;
if (HAL_DMA_Init(&hdma_usart2_tx) != HAL_OK)
{
Error_Handler();
}
/* Associate the initialized DMA handle to the UART handle */
__HAL_LINKDMA(huart, hdmatx, hdma_usart2_tx);
/* Enable the DMA transfer complete interrupt */
__HAL_UART_ENABLE_IT(huart, UART_IT_TC);
```
注意:上述代码中,使用的是USART2和DMA1_Channel4,你需要根据实际情况进行调整。
5. 在生成的代码中找到`USART_Transmit()`函数,一般位于`usart.c`文件中。在该函数中添加以下代码,用于启动DMA传输:
```c
/* Set the DMA transfer complete callback */
huart->hdmatx->XferCpltCallback = UART_DMA_TransmitCplt;
/* Start the DMA transfer */
HAL_DMA_Start_IT(huart->hdmatx, (uint32_t)str, strlen(str));
```
6. 最后,在生成的代码中找到`USART_IRQHandler()`函数,一般位于`stm32f4xx_it.c`文件中。在该函数中添加以下代码,用于处理DMA传输完成的中断:
```c
/* USART2 DMA Transmit Complete Interrupt */
void DMA1_Channel4_IRQHandler(void)
{
/* Check the DMA interrupt flag */
if (__HAL_DMA_GET_IT_SOURCE(huart2.hdmatx, DMA_IT_TC) != RESET)
{
/* Clear the DMA interrupt flag */
__HAL_DMA_CLEAR_FLAG(huart2.hdmatx, DMA_IT_TC);
/* Disable the DMA transfer complete interrupt */
__HAL_DMA_DISABLE_IT(huart2.hdmatx, DMA_IT_TC);
/* Call the DMA transmit complete callback function */
HAL_UART_TxCpltCallback(&huart2);
}
}
```
完成以上步骤后,你就可以在代码中使用标准的`printf`函数,输出的内容会通过DMA传输到串口中。
希望这对你有帮助!如有更多问题,请继续提问。
hal库dma串口发送 printf 重定向
您可以使用HAL库的DMA传输功能来实现printf重定向到串口的功能。具体步骤如下:
1. 在main.c中添加以下头文件:
```c
#include "stdio.h"
#include "stdarg.h"
#include "stm32f4xx_hal.h"
```
2. 定义一个用于重定向的缓冲区:
```c
#define UART_TX_BUFFER_SIZE 1024
char uart_tx_buffer[UART_TX_BUFFER_SIZE];
```
3. 定义一个printf重定向函数,该函数将数据格式化后传输到串口:
```c
int __io_putchar(int ch)
{
static uint16_t pos = 0;
uart_tx_buffer[pos++] = (uint8_t)ch;
if (pos >= UART_TX_BUFFER_SIZE)
{
HAL_UART_Transmit_DMA(&huart2, (uint8_t*)uart_tx_buffer, pos);
pos = 0;
}
return ch;
}
int _write(int file, char *ptr, int len)
{
for (int i = 0; i < len; i++)
{
__io_putchar(*ptr++);
}
return len;
}
```
该函数将数据传输到UART2的DMA中,并在缓冲区填满时自动启动DMA传输。
4. 在main函数中初始化串口和DMA:
```c
int main(void)
{
HAL_Init();
SystemClock_Config();
MX_GPIO_Init();
MX_DMA_Init();
MX_USART2_UART_Init();
// 重定向printf到串口
printf("Hello, world!\r\n");
while (1)
{
}
}
```
5. 在stm32f4xx_hal_conf.h中启用DMA:
```c
#define HAL_UART_MODULE_ENABLED
#define HAL_DMA_MODULE_ENABLED
```
完成上述步骤后,即可使用printf函数将数据重定向到串口,并使用DMA进行传输。