GPIOB->CRH&=0XFFFFFF0F;GPIOB->CRH|=8<<4
时间: 2024-05-27 21:10:16 浏览: 14
这段代码是针对STM32系列单片机的,作用是将GPIOB的第4个引脚配置为输出模式,输出速率为最高速率50MHz。
具体来说,GPIOB是一个GPIO端口的指针,通过->符号调用该端口的寄存器。CRH是GPIOB的控制寄存器高位,用来配置GPIOB的8个引脚,每个引脚占用4个bit位。因此,&=0XFFFFFF0F用来清除第4个引脚的配置,保留其他引脚的配置;|=8<<4用来将第4个引脚的配置设置为输出模式,最高速率50MHz。其中,8表示输出模式,<<4表示将8左移4位,即将8的二进制码00001000左移4位得到10000000,即第4个bit位为1,表示该引脚为输出模式。
综上所述,这段代码的作用是将GPIOB的第4个引脚配置为输出模式,输出速率为最高速率50MHz。
相关问题
GPIOB->CRH&=0XFFFFFF0F;GPIOB->CRH|=8<<12;怎么配置
GPIOB->CRH refers to the configuration register high of the GPIOB port. It is a 32-bit register that is used to configure the behavior of the pins of the GPIOB port. Each pin of the port has 4 bits in this register which are used to configure the pin mode, output type, speed, and pull-up/pull-down resistors.
The CRH register is used for the pins 8 to 15 of the GPIOB port, while the CRL register is used for the pins 0 to 7. The configuration of the pins can be set using bitwise operations and constants defined in the STM32F103xx.h header file.
For example, to set pin 12 of GPIOB as an output pin with a maximum output speed of 50 MHz, the following code can be used:
GPIOB->CRH |= GPIO_CRH_MODE12; // Set pin 12 as output
GPIOB->CRH |= GPIO_CRH_CNF12_1; // Set pin 12 as push-pull output
GPIOB->CRH |= GPIO_CRH_MODE12_1; // Set pin 12 to maximum output speed of 50 MHz
Note that this code assumes that the GPIOB clock has already been enabled and that the appropriate pins have been configured as GPIO pins using the GPIOB->CRL register.
GPIOB->CRH|=0XB8B00000;
GPIOB->CRH |= 0xB8B00000; 是一条C语言代码,用于设置GPIOB的控制寄存器高位(CRH)的值为0xB8B00000。这条代码的作用是配置GPIOB的引脚功能和模式。
具体解释如下:
- GPIOB:表示要配置的GPIO端口为GPIOB。
- CRH:表示GPIOB的控制寄存器高位,用于配置引脚8到15的功能和模式。
- |=:表示按位或运算符,将CRH寄存器的值与0xB8B00000进行按位或操作。
- 0xB8B00000:表示要设置的值,以二进制形式表示为10111000101100000000000000000。
根据这个设置,GPIOB的引脚8到15将被配置为特定的功能和模式,具体的功能和模式取决于0xB8B00000的二进制表示。请注意,具体的功能和模式需要参考相关的芯片手册或开发板文档来确定。