基于STM32的的DHT20子程序流程图
时间: 2024-05-05 19:21:43 浏览: 14
很抱歉,我作为一个语言模型,无法直接生成流程图。但我可以为您提供一些基于STM32的DHT20子程序的代码框架,供您参考:
```c
#include "stm32f10x.h"
#include "delay.h"
#include "dht20.h"
// 定义DHT20的引脚
#define DHT20_PORT GPIOB
#define DHT20_PIN GPIO_Pin_0
// 定义读取DHT20数据的延时时间
#define DHT20_DELAY_TIME 30
// DHT20初始化函数
void DHT20_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// 使能GPIOB的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);
// 配置DHT20引脚为输出
GPIO_InitStructure.GPIO_Pin = DHT20_PIN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(DHT20_PORT, &GPIO_InitStructure);
}
// DHT20发送起始信号
void DHT20_Start(void)
{
// 将DHT20引脚置为输出
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = DHT20_PIN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(DHT20_PORT, &GPIO_InitStructure);
// 发送起始信号
GPIO_SetBits(DHT20_PORT, DHT20_PIN);
delay_ms(1);
GPIO_ResetBits(DHT20_PORT, DHT20_PIN);
delay_ms(20);
GPIO_SetBits(DHT20_PORT, DHT20_PIN);
delay_us(30);
}
// DHT20等待响应信号
void DHT20_WaitResponse(void)
{
// 将DHT20引脚置为输入
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = DHT20_PIN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(DHT20_PORT, &GPIO_InitStructure);
// 等待DHT20响应信号
while(GPIO_ReadInputDataBit(DHT20_PORT, DHT20_PIN) == Bit_SET);
while(GPIO_ReadInputDataBit(DHT20_PORT, DHT20_PIN) == Bit_RESET);
while(GPIO_ReadInputDataBit(DHT20_PORT, DHT20_PIN) == Bit_SET);
}
// DHT20读取数据
uint8_t DHT20_ReadData(void)
{
uint8_t i, j, value = 0;
// 读取DHT20数据
for(i = 0; i < 8; i++)
{
while(GPIO_ReadInputDataBit(DHT20_PORT, DHT20_PIN) == Bit_RESET);
delay_us(DHT20_DELAY_TIME);
if(GPIO_ReadInputDataBit(DHT20_PORT, DHT20_PIN) == Bit_SET)
{
value |= (1 << (7 - i));
}
while(GPIO_ReadInputDataBit(DHT20_PORT, DHT20_PIN) == Bit_SET);
}
return value;
}
// DHT20读取温湿度数据
void DHT20_ReadTHData(float *temp, float *humi)
{
uint8_t buf[5] = {0};
uint16_t sum = 0;
// 发送起始信号
DHT20_Start();
// 等待响应信号
DHT20_WaitResponse();
// 读取数据
buf[0] = DHT20_ReadData();
buf[1] = DHT20_ReadData();
buf[2] = DHT20_ReadData();
buf[3] = DHT20_ReadData();
buf[4] = DHT20_ReadData();
// 计算校验和
sum = buf[0] + buf[1] + buf[2] + buf[3];
// 判断校验和是否正确
if(sum == buf[4])
{
// 计算温度和湿度
*humi = (float)(buf[0] << 8 | buf[1]) / 10.0;
*temp = (float)(buf[2] << 8 | buf[3]) / 10.0;
}
else
{
// 校验和错误,温湿度数据无效
*humi = 0;
*temp = 0;
}
}
```
以上代码是一个基本的DHT20子程序框架,其中包括DHT20的初始化、发送起始信号、等待响应信号、读取数据和计算温湿度等功能。您可以根据自己的需要进行修改和完善。