opt3006与stm32f103c8t6怎么连接
时间: 2023-06-02 18:04:21 浏览: 72
可以通过I2C总线进行连接。首先需要将OPT3006的SDA和SCL引脚分别连接到STM32F103C8T6的I2C1的SDA和SCL引脚上,并在STM32F103C8T6上配置I2C1作为从设备,然后就可以通过I2C总线进行通信了。
相关问题
stm32f103c8t6上写opt101的代码要如何写
在STM32F103C8T6上使用Opt101光电传感器,需要先将其连接到STM32F103C8T6的模拟输入引脚上,然后编写相应的代码来读取传感器输出的电压信号。以下是一个简单的示例代码:
```c
#include "stm32f10x.h"
#define ADC1_DR_Address ((u32)0x4001244C)
void ADC1_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
ADC_InitTypeDef ADC_InitStructure;
// 开启GPIO和ADC1的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_ADC1, ENABLE);
// 配置PA1为模拟输入引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// ADC1配置
ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;
ADC_InitStructure.ADC_ScanConvMode = DISABLE;
ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
ADC_InitStructure.ADC_NbrOfChannel = 1;
ADC_Init(ADC1, &ADC_InitStructure);
// 启动ADC1
ADC_Cmd(ADC1, ENABLE);
// 配置ADC1通道1
ADC_RegularChannelConfig(ADC1, ADC_Channel_1, 1, ADC_SampleTime_239Cycles5);
// 清除标志位
ADC_ClearFlag(ADC1, ADC_FLAG_EOC);
// 启用ADC1的DMA
ADC_DMACmd(ADC1, ENABLE);
// 启动ADC1的校准
ADC_ResetCalibration(ADC1);
while (ADC_GetResetCalibrationStatus(ADC1));
ADC_StartCalibration(ADC1);
while (ADC_GetCalibrationStatus(ADC1));
}
u16 ADC1_Read(void)
{
u16 ADC_Value;
// 启动ADC1转换
ADC_SoftwareStartConvCmd(ADC1, ENABLE);
// 等待转换完成
while (ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET);
// 读取转换结果
ADC_Value = ADC_GetConversionValue(ADC1);
return ADC_Value;
}
int main(void)
{
u16 adc_value;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
// 初始化ADC1
ADC1_Init();
while (1)
{
// 读取ADC1的值
adc_value = ADC1_Read();
// 进行一些处理得到光照强度值
// ...
// 延时
Delay(100);
}
}
```
在这个示例代码中,我们使用STM32F103C8T6的ADC1模块来读取Opt101光电传感器的输出电压信号。首先在ADC1初始化函数`ADC1_Init()`中配置ADC1的一些参数,包括模拟输入引脚、采样时间等。然后在`ADC1_Read()`函数中启动ADC1的转换,等待转换完成后读取转换结果。最后在`main()`函数中可以进行一些处理,得到光照强度值。需要注意的是,由于Opt101输出的是电压信号,因此还需要进行一些电路设计和计算,将电压转换为光照强度值。
stm32f103c8t6添加OLED显示屏库文件
要在STM32F103C8T6上使用OLED显示屏,需要先下载相应的库文件。常见的OLED显示屏库文件有u8glib、Adafruit_SSD1306等,根据自己的需求选择合适的库文件。
以下是使用u8glib库文件的步骤:
1. 下载u8glib库文件。可以在GitHub上下载,也可以在官网上下载。
2. 将u8glib库文件添加到工程中。将下载的库文件解压缩,将u8glib文件夹复制到工程目录下,然后在工程中添加库文件。
3. 在代码中调用库文件。在代码中引入库文件头文件,并在main函数中初始化OLED显示屏,然后调用相关函数进行显示。
以下是一个简单的示例代码:
```
#include "u8glib.h"
u8g_t u8g;
int main(void)
{
u8g_Init(&u8g, &u8g_dev_ssd1306_128x64_i2c, U8G_I2C_OPT_NONE);
u8g_SetFont(&u8g, u8g_font_6x10);
u8g_DrawStr(&u8g, 0, 20, "Hello World!");
u8g_SendBuffer(&u8g);
while(1);
}
```
其中,u8g_Init函数用于初始化OLED显示屏,u8g_SetFont函数用于设置字体,u8g_DrawStr函数用于在OLED上绘制字符串,u8g_SendBuffer函数用于将画面发送到OLED显示屏上。具体函数的使用方法可以参考u8glib的文档。
相关推荐
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)