详细说明PIN类型open drain output
时间: 2023-11-02 12:30:19 浏览: 32
Open drain output是一种数字输出类型,它通常用于单片机或其他数字电路中。在该类型的输出中,输出管(通常是N-MOSFET管)的源极连接到地,而漏极作为输出端。因此,输出端只能够拉低至地,而不能够主动拉高。这种输出类型通常用于控制外部电路的开关,例如LED的亮灭控制、继电器的开闭控制等。
由于open drain output只能拉低输出端,因此通常需要与上拉电阻结合使用,以实现输出端的高电平。当输出管关闭时,上拉电阻将输出端拉高至电源电压,当输出管打开时,输出端会被拉低至地,从而实现控制外部电路的开闭。
需要注意的是,由于输出端只能拉低,因此在使用open drain output时需要注意电路的连接,以免出现输出端短路的情况。此外,在使用open drain output时,还需要注意输出端的最大驱动电流和最大负载电容,以保证电路正常工作。
相关问题
open drain output
Open drain output is a type of electronic output that can either be in the high-impedance state or sink current to ground. In this type of output, the transistor is connected between the output pin and ground, and it can be turned on or off by applying a control signal to the gate. When the transistor is turned off, the output pin is in the high-impedance state, which means that it is not connected to anything. When the transistor is turned on, current can flow from the output pin to ground, which allows the output to sink current. Open drain outputs are commonly used in digital circuits to interface with other devices that have different voltage levels or to drive signals over long distances.
typedef struct _IMUInterruptPinSetting { /** To enable either INT1 or INT2 pin as output. * 0- output disabled ,1- output enabled */ uint16_t output_en : 1; /** 0 - push-pull 1- open drain,only valid if output_en is set 1 */ uint16_t output_mode : 1; /** 0 - active low , 1 - active high level. * if output_en is 1,this applies to interrupts,else PMU_trigger */ uint16_t output_type : 1; /** 0 - level trigger , 1 - edge trigger */ uint16_t edge_ctrl : 1; /** To enable either INT1 or INT2 pin as input. * 0 - input disabled ,1 - input enabled */ uint16_t input_en : 1; /** latch duration*/ uint16_t latch_dur : 4; } IMUInterruptPinSetting;尝试解释
这段代码定义了一个名为_IMUInterruptPinSetting的结构体,其中包含了用于配置中断引脚的各种参数。具体来说,这个结构体包含了以下字段:
1. output_en:用于使能INT1或INT2引脚的输出功能。当其值为0时,输出功能被禁用;当其值为1时,输出功能被启用。
2. output_mode:用于配置输出模式,当output_en为1时有效。当其值为0时,输出为推挽模式;当其值为1时,输出为开漏模式。
3. output_type:用于配置输出电平类型。当output_en为1时,该配置项适用于中断;否则,适用于PMU_trigger。当其值为0时,输出电平为低电平;当其值为1时,输出电平为高电平。
4. edge_ctrl:用于选择中断是边沿触发还是电平触发。当其值为0时,中断是电平触发;当其值为1时,中断是边沿触发。
5. input_en:用于启用或禁用INT1或INT2引脚的输入功能。当其值为0时,输入功能被禁用;当其值为1时,输入功能被启用。
6. latch_dur:用于配置中断锁存的持续时间。其值表示中断锁存的持续时间,单位为时钟周期。