ESP8266_RST_Pin
时间: 2024-08-12 14:08:52 浏览: 54
ESP8266是一个常用的Wi-Fi模块,其RST_Pin(Reset Pin)是复位引脚。当RST_Pin被外部低电平信号触发时,ESP8266会进入初始化状态,也就是重新启动。这个引脚通常用于系统重启、升级固件或者在开发过程中恢复模块到初始状态。
- **作用**:在编程过程中,RST_Pin可以用于强制模块重启或恢复出厂设置,以便于调试和固件更新。
- **连接**:在硬件设计中,RST_Pin通常连接到主板上的GPIO(通用输入/输出)引脚,可以通过外部电路(如跳线、按钮或微控制器控制)来控制它的高/低状态。
- **注意事项**:在实际应用中,正确使用RST_Pin可以避免意外重启导致的数据丢失,但频繁重启也可能对模块寿命造成影响。
相关问题
stm32f103连接esp8266
在连接STM32F103和ESP8266时,你需要注意以下几点。首先,确保你的串口连接正确,不要接错串口,否则ESP8266会初始化失败。其次,你需要在代码中正确配置ESP8266的相关参数,包括client_id等。在配置完成后,你可以通过串口助手来查看连接状态,同时阿里云平台也会显示在线状态。最后,你可以使用宏定义来控制ESP8266的复位引脚,例如使用#define ESP8266_RST_Pin_SetH来设置引脚为高电平,使用#define ESP8266_RST_Pin_SetL来设置引脚为低电平。
#### 引用[.reference_title]
- *1* [stm32f103与esp8266通信](https://blog.csdn.net/qq_63742188/article/details/131197647)[target="_blank" data-report-click={"spm":"1018.2226.3001.9630","extra":{"utm_source":"vip_chatgpt_common_search_pc_result","utm_medium":"distribute.pc_search_result.none-task-cask-2~all~insert_cask~default-1-null.142^v91^control_2,239^v3^insert_chatgpt"}} ] [.reference_item]
- *2* [STM32F103+ESP8266接入阿里云平台(曲折的上云之路)](https://blog.csdn.net/qq_51963216/article/details/122541616)[target="_blank" data-report-click={"spm":"1018.2226.3001.9630","extra":{"utm_source":"vip_chatgpt_common_search_pc_result","utm_medium":"distribute.pc_search_result.none-task-cask-2~all~insert_cask~default-1-null.142^v91^control_2,239^v3^insert_chatgpt"}} ] [.reference_item]
- *3* [关于esp8266模块与stm32f103模块的连接,问题分析](https://blog.csdn.net/Antonhu/article/details/130874612)[target="_blank" data-report-click={"spm":"1018.2226.3001.9630","extra":{"utm_source":"vip_chatgpt_common_search_pc_result","utm_medium":"distribute.pc_search_result.none-task-cask-2~all~insert_cask~default-1-null.142^v91^control_2,239^v3^insert_chatgpt"}} ] [.reference_item]
[ .reference_list ]
可以帮我写一个基于stm32f103c8t6、esp8266串口WiFi和手机连接的代码
当然可以,以下是一个简单的示例代码,实现了stm32f103c8t6和esp8266之间的串口通信,并且可以通过WiFi与手机连接进行数据交互。
```c
#include "stm32f10x.h"
#include <stdio.h>
#include <string.h>
#define USART1_RX_GPIO_PORT GPIOA
#define USART1_RX_GPIO_CLK RCC_APB2Periph_GPIOA
#define USART1_RX_PIN GPIO_Pin_10
#define USART1_TX_GPIO_PORT GPIOA
#define USART1_TX_GPIO_CLK RCC_APB2Periph_GPIOA
#define USART1_TX_PIN GPIO_Pin_9
#define ESP8266_USART USART1
#define ESP8266_USART_CLK RCC_APB2Periph_USART1
#define ESP8266_USART_BAUDRATE 115200
#define ESP8266_RST_GPIO_PORT GPIOA
#define ESP8266_RST_GPIO_CLK RCC_APB2Periph_GPIOA
#define ESP8266_RST_PIN GPIO_Pin_8
#define ESP8266_CH_PD_GPIO_PORT GPIOA
#define ESP8266_CH_PD_GPIO_CLK RCC_APB2Periph_GPIOA
#define ESP8266_CH_PD_PIN GPIO_Pin_7
#define WIFI_SSID "your_wifi_ssid"
#define WIFI_PASSWORD "your_wifi_password"
#define SERVER_IP "192.168.1.100"
#define SERVER_PORT "8080"
#define BUFFER_SIZE 128
void USART_Config(void);
void GPIO_Config(void);
void ESP8266_Init(void);
void ESP8266_ConnectWiFi(void);
void ESP8266_ConnectServer(void);
void ESP8266_SendData(char* data);
int main(void) {
char buffer[BUFFER_SIZE];
USART_Config();
GPIO_Config();
ESP8266_Init();
ESP8266_ConnectWiFi();
ESP8266_ConnectServer();
while (1) {
// 读取串口数据
if (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == SET) {
char data = USART_ReceiveData(ESP8266_USART);
if (data == '\n' || data == '\r') {
buffer[strlen(buffer)] = '\0';
ESP8266_SendData(buffer); // 发送数据到服务器
buffer[0] = '\0';
} else {
strncat(buffer, &data, 1);
}
}
}
}
void USART_Config(void) {
USART_InitTypeDef USART_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(ESP8266_USART_CLK | USART1_TX_GPIO_CLK | USART1_RX_GPIO_CLK, ENABLE);
/* USART1_TX GPIO pin configuration */
GPIO_InitStructure.GPIO_Pin = USART1_TX_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(USART1_TX_GPIO_PORT, &GPIO_InitStructure);
/* USART1_RX GPIO pin configuration */
GPIO_InitStructure.GPIO_Pin = USART1_RX_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(USART1_RX_GPIO_PORT, &GPIO_InitStructure);
/* USART1 configuration */
USART_InitStructure.USART_BaudRate = ESP8266_USART_BAUDRATE;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(ESP8266_USART, &USART_InitStructure);
/* Enable USART1 */
USART_Cmd(ESP8266_USART, ENABLE);
}
void GPIO_Config(void) {
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(ESP8266_RST_GPIO_CLK | ESP8266_CH_PD_GPIO_CLK, ENABLE);
/* Configure RESET pin */
GPIO_InitStructure.GPIO_Pin = ESP8266_RST_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(ESP8266_RST_GPIO_PORT, &GPIO_InitStructure);
/* Configure CH_PD pin */
GPIO_InitStructure.GPIO_Pin = ESP8266_CH_PD_PIN;
GPIO_Init(ESP8266_CH_PD_GPIO_PORT, &GPIO_InitStructure);
/* Reset ESP8266 module */
GPIO_SetBits(ESP8266_RST_GPIO_PORT, ESP8266_RST_PIN);
GPIO_SetBits(ESP8266_CH_PD_GPIO_PORT, ESP8266_CH_PD_PIN);
GPIO_ResetBits(ESP8266_RST_GPIO_PORT, ESP8266_RST_PIN);
for (int i = 0; i < 5000000; i++);
GPIO_SetBits(ESP8266_RST_GPIO_PORT, ESP8266_RST_PIN);
for (int i = 0; i < 5000000; i++);
}
void ESP8266_Init(void) {
char buffer[BUFFER_SIZE];
USART_SendData(ESP8266_USART, "AT\r\n");
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_TXE) == RESET);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
USART_ReceiveData(ESP8266_USART);
USART_SendData(ESP8266_USART, "AT+CWMODE=1\r\n");
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_TXE) == RESET);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
USART_ReceiveData(ESP8266_USART);
USART_SendData(ESP8266_USART, "AT+RST\r\n");
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_TXE) == RESET);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
USART_ReceiveData(ESP8266_USART);
for (int i = 0; i < 5000000; i++);
USART_SendData(ESP8266_USART, "AT+CWJAP=\"" WIFI_SSID "\",\"" WIFI_PASSWORD "\"\r\n");
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_TXE) == RESET);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
USART_ReceiveData(ESP8266_USART);
for (int i = 0; i < 10000000; i++);
}
void ESP8266_ConnectWiFi(void) {
char buffer[BUFFER_SIZE];
USART_SendData(ESP8266_USART, "AT+CWJAP?\r\n");
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_TXE) == RESET);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
USART_ReceiveData(ESP8266_USART);
for (int i = 0; i < 5000000; i++);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
char data = USART_ReceiveData(ESP8266_USART);
while (data != '\r') {
strncat(buffer, &data, 1);
data = USART_ReceiveData(ESP8266_USART);
}
if (strstr(buffer, WIFI_SSID) != NULL) {
printf("Connected to WiFi: %s\n", WIFI_SSID);
} else {
printf("Failed to connect to WiFi: %s\n", WIFI_SSID);
}
}
void ESP8266_ConnectServer(void) {
char buffer[BUFFER_SIZE];
USART_SendData(ESP8266_USART, "AT+CIPSTART=\"TCP\",\"" SERVER_IP "\"," SERVER_PORT "\r\n");
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_TXE) == RESET);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
USART_ReceiveData(ESP8266_USART);
for (int i = 0; i < 5000000; i++);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
char data = USART_ReceiveData(ESP8266_USART);
while (data != '\r') {
strncat(buffer, &data, 1);
data = USART_ReceiveData(ESP8266_USART);
}
if (strstr(buffer, "CONNECT") != NULL) {
printf("Connected to server: %s:%s\n", SERVER_IP, SERVER_PORT);
} else {
printf("Failed to connect to server: %s:%s\n", SERVER_IP, SERVER_PORT);
}
}
void ESP8266_SendData(char* data) {
int len = strlen(data);
char buffer[BUFFER_SIZE];
sprintf(buffer, "AT+CIPSEND=%d\r\n", len);
USART_SendData(ESP8266_USART, buffer);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_TXE) == RESET);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
USART_ReceiveData(ESP8266_USART);
for (int i = 0; i < 5000000; i++);
USART_SendData(ESP8266_USART, data);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_TXE) == RESET);
while (USART_GetFlagStatus(ESP8266_USART, USART_FLAG_RXNE) == RESET);
USART_ReceiveData(ESP8266_USART);
for (int i = 0; i < 5000000; i++);
}
```
注意,这只是一个简单的示例代码,可能需要根据实际情况进行修改和优化。
阅读全文