stml9110风扇模块驱动代码
时间: 2023-11-12 09:47:42 浏览: 162
STML9110 风扇模块驱动代码需要根据具体的硬件设计进行编写。以下是一些常见的风扇模块驱动代码示例,供参考:
1. 使用PWM模块控制风扇转速
```
#include "stm32l1xx_hal.h"
/* 定义PWM输出引脚 */
#define FAN_PWM_PIN GPIO_PIN_1
#define FAN_PWM_PORT GPIOA
/* 定义PWM模块 */
TIM_HandleTypeDef htim3;
/* 风扇初始化函数 */
void fan_init(void)
{
/* 使能PWM时钟 */
__HAL_RCC_TIM3_CLK_ENABLE();
/* 配置PWM引脚 */
GPIO_InitTypeDef GPIO_InitStruct = {0};
GPIO_InitStruct.Pin = FAN_PWM_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF2_TIM3;
HAL_GPIO_Init(FAN_PWM_PORT, &GPIO_InitStruct);
/* 配置PWM模块 */
htim3.Instance = TIM3;
htim3.Init.Prescaler = 0;
htim3.Init.CounterMode = TIM_COUNTERMODE_UP;
htim3.Init.Period = 999;
htim3.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
HAL_TIM_PWM_Init(&htim3);
/* 启动PWM模块 */
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_4);
}
/* 设置风扇转速 */
void fan_set_speed(uint8_t speed)
{
/* 计算占空比 */
uint32_t duty_cycle = speed * 10;
/* 设置PWM占空比 */
TIM_OC_InitTypeDef sConfigOC = {0};
sConfigOC.OCMode = TIM_OCMODE_PWM1;
sConfigOC.Pulse = duty_cycle;
sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
HAL_TIM_PWM_ConfigChannel(&htim3, &sConfigOC, TIM_CHANNEL_4);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_4);
}
```
2. 使用GPIO模块控制风扇开关
```
#include "stm32l1xx_hal.h"
/* 定义GPIO输出引脚 */
#define FAN_GPIO_PIN GPIO_PIN_1
#define FAN_GPIO_PORT GPIOA
/* 风扇初始化函数 */
void fan_init(void)
{
/* 使能GPIO时钟 */
__HAL_RCC_GPIOA_CLK_ENABLE();
/* 配置GPIO引脚 */
GPIO_InitTypeDef GPIO_InitStruct = {0};
GPIO_InitStruct.Pin = FAN_GPIO_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(FAN_GPIO_PORT, &GPIO_InitStruct);
}
/* 打开风扇 */
void fan_turn_on(void)
{
HAL_GPIO_WritePin(FAN_GPIO_PORT, FAN_GPIO_PIN, GPIO_PIN_SET);
}
/* 关闭风扇 */
void fan_turn_off(void)
{
HAL_GPIO_WritePin(FAN_GPIO_PORT, FAN_GPIO_PIN, GPIO_PIN_RESET);
}
```
需要根据具体的硬件设计,选择适合的代码进行修改。
阅读全文