使用c++写一个OLED显示驱动程序
时间: 2023-03-30 12:01:24 浏览: 91
好的,我可以回答这个问题。使用 C 语言编写 OLED 显示驱动程序需要了解 OLED 的通信协议和控制命令,以及具体的硬件接口。一般来说,需要使用 GPIO 控制 OLED 的 CS、DC、RES 等引脚,同时通过 SPI 或 I2C 等总线协议与 OLED 进行通信。具体实现方式可以参考 OLED 的数据手册和硬件接口文档。
相关问题
使用c++写一个OLED显示驱动程序加上注释
非常感谢您的问题,我可以回答这个问题。以下是一个使用 C 语言编写的 OLED 显示驱动程序的示例代码,其中包括注释:
```
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/ioctl.h>
#include <linux/i2c-dev.h>
#define OLED_I2C_ADDR x3C // OLED 显示器的 I2C 地址
// OLED 显示器的初始化命令序列
const unsigned char init_cmds[] = {
xAE, // 关闭显示
xD5, x80, // 设置时钟分频因子,震荡器频率
xA8, x3F, // 设置驱动路数
xD3, x00, // 设置显示偏移
x40, // 设置显示开始行 [5:]
x8D, x14, // 启用电荷泵
x20, x00, // 设置内存地址模式
xA1, // 指定段重定向
xC8, // 设置扫描方向
xDA, x12, // 设置 COM 硬件引脚配置
x81, xCF, // 设置对比度
xD9, xF1, // 设置预充电周期
xDB, x40, // 设置 VCOMH 电压倍率
xA4, // 关闭全局显示
xA6, // 设置显示方式
xAF // 打开显示
};
// 初始化 OLED 显示器
void oled_init(int fd) {
int i;
for (i = ; i < sizeof(init_cmds); i++) {
unsigned char cmd[2] = {x00, init_cmds[i]};
if (write(fd, cmd, sizeof(cmd)) != sizeof(cmd)) {
perror("write");
exit(1);
}
}
}
// 在 OLED 显示器上显示一行文本
void oled_write_line(int fd, int line, const char *text) {
int i;
unsigned char cmd[2] = {x00, xB + line};
if (write(fd, cmd, sizeof(cmd)) != sizeof(cmd)) {
perror("write");
exit(1);
}
cmd[] = x40;
for (i = ; i < 16; i++) {
if (*text) {
cmd[1] = *text++;
} else {
cmd[1] = ' ';
}
if (write(fd, cmd, sizeof(cmd)) != sizeof(cmd)) {
perror("write");
exit(1);
}
}
}
int main(int argc, char *argv[]) {
int fd;
const char *dev = "/dev/i2c-1";
if ((fd = open(dev, O_RDWR)) < ) {
perror("open");
exit(1);
}
if (ioctl(fd, I2C_SLAVE, OLED_I2C_ADDR) < ) {
perror("ioctl");
exit(1);
}
oled_init(fd);
oled_write_line(fd, , "Hello, world!");
close(fd);
return ;
}
```
希望这个示例代码能够对您有所帮助。
arduino驱动0.96寸OLED屏幕程序
以下是使用 Arduino 驱动 0.96 寸 OLED 屏幕的程序:
```C++
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#define OLED_RESET 4
Adafruit_SSD1306 display(OLED_RESET);
void setup() {
display.begin(SSD1306_SWITCHCAPVCC, 0x3C); // 初始化屏幕
display.display();
delay(2000); // 显示 2 秒
display.clearDisplay(); // 清空屏幕
}
void loop() {
display.setTextSize(2); // 设置字体大小
display.setTextColor(WHITE); // 设置字体颜色
display.setCursor(0, 0); // 设置光标位置
display.println("Hello, world!"); // 显示文本
display.display(); // 刷新屏幕
delay(2000); // 显示 2 秒
display.clearDisplay(); // 清空屏幕
}
```
其中需要安装 `Adafruit_GFX` 和 `Adafruit_SSD1306` 库。在 `setup` 函数中,我们初始化 OLED 屏幕,并在 `loop` 函数中显示一段文本,并清空屏幕,然后再重复这个过程。